From: Nir Wittenberg (nwittenberg@msncomm.com)
Date: Fri Oct 17 2003 - 13:01:10 GMT-3
Thank you to all for your replies. It was the mincir tripping me up.
Nir
-----Original Message-----
From: asadovnikov [mailto:asadovnikov@comcast.net]
Sent: Thursday, October 16, 2003 7:24 PM
To: Nir Wittenberg; ccielab@groupstudy.com
Subject: RE: QOS error message
On frame relay perVC queue you can allocate mincir bandwidth (regardless
of your interface bandwidth and/or max-reserved settings). When mincir
is not configured it is 50% of cir, hence the issue. Try to configure
mincir 768000 in map-class frame-relay 768k and your issue should be
fixed.
BTW, Setting mincir = cir (and both equal to contracted CIR from you
provider) and switching off adaptive shaping are recommended settings
for voice.
Best regards,
Alexei
-----Original Message-----
From: Nir Wittenberg [mailto:nwittenberg@msncomm.com]
Sent: Thursday, October 16, 2003 9:00 PM
To: asadovnikov; ccielab@groupstudy.com
Subject: RE: QOS error message
sh ver
Cisco Internetwork Operating System Software
IOS (tm) C1700 Software (C1700-SV3Y-M), Version 12.2(2)XK2, EARLY
DEPLOYMENT REL EASE SOFTWARE (fc1) TAC Support: http://www.cisco.com/tac
Copyright (c) 1986-2002 by cisco Systems, Inc. Compiled Sat 16-Feb-02
22:54 by ealyon Image text-base: 0x80008124, data-base: 0x80D358C4
ROM: System Bootstrap, Version 12.2(4r)XL, RELEASE SOFTWARE (fc1)
ROM: C1700 Software (C1700-SV3Y-M), Version 12.2(2)XK2, EARLY DEPLOYMENT
RELEASE SOFTWARE (fc1)
MC_215Union uptime is 6 days, 4 hours, 8 minutes
System returned to ROM by power-on
System image file is "flash:c1700-sv3y-mz.122-2.XK2.bin"
cisco 1760 (MPC860P) processor (revision 0x200) with 58983K/6553K bytes
of memor y. Processor board ID VMS061000BZ (3832917203), with hardware
revision BB67 MPC860P processor: part number 5, mask 2 Bridging
software. X.25 software, Version 3.0.0. 1 FastEthernet/IEEE 802.3
interface(s) 1 Serial network interface(s) 2 Voice FXO interface(s) WIC
T1-DSU 32K bytes of non-volatile configuration memory. 32768K bytes of
processor board System flash (Read/Write)
Configuration register is 0x2102
sh run
Building configuration...
Current configuration : 2617 bytes
!
version 12.2
service timestamps debug uptime
service timestamps log uptime
service password-encryption
!
ip subnet-zero
!
!
!
ip cef
!
class-map match-any voice-control
match access-group name voice-control
class-map match-all voice
match ip precedence 5
match ip rtp 16384 16383
!
!
policy-map wan-qos
class voice
set ip dscp 46
priority 512
class voice-control
bandwidth 64
!
interface Serial0/0
bandwidth 1536
no ip address
encapsulation frame-relay
!
interface Serial0/0.16 point-to-point
bandwidth 768
ip address 10.202.254.90 255.255.255.252
frame-relay class 768k
frame-relay interface-dlci 16
!
interface Serial0/0.17 point-to-point
bandwidth 768
ip address 10.11.254.6 255.255.255.252
delay 10000
frame-relay class 768k
frame-relay interface-dlci 17
!
!
ip access-list extended voice-control
remark Permit H.323
permit tcp any any eq 1720
remark Permit SCCP
permit tcp any any range 2000 2002
remark Permit MGCP
permit udp any any eq 2427
permit tcp any any eq 2428
!
map-class frame-relay 768k
frame-relay cir 768000
frame-relay bc 7680
frame-relay be 0
no frame-relay adaptive-shaping
service-policy output wan-qos
As soon as I add the frame-relay traffic shaping command to int s0/0 I
get the error message and the service-policy output commnad is removed
from the map-class 768k.
Thanks,
Nir
-----Original Message-----
From: asadovnikov [mailto:asadovnikov@comcast.net]
Sent: Thursday, October 16, 2003 6:50 PM
To: Nir Wittenberg; ccielab@groupstudy.com
Subject: RE: QOS error message
Could you possibly send configuration of your serial
interface/subinterface, QOS classes/policies, any frame class parameters
(i.e. shaping) + IOS version. As per earlier mail it so looks that IOS
trusts you do not have enough bandwidth to apply while you think
different. The question is why.
Best regards,
Alexei
-----Original Message-----
From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
Nir Wittenberg
Sent: Thursday, October 16, 2003 8:31 PM
To: Hale, Wendy; ccielab@groupstudy.com
Subject: RE: QOS error message
My policy-map gives a priority of 512. Under my subinterfaces I have
bandwidth statements of 768. So it is in the range. I also used the
max-reserved-bandwidth 100 command under the main interface with the
same result.
Nir
-----Original Message-----
From: Hale, Wendy [mailto:WRHale@NECBNS.com]
Sent: Thursday, October 16, 2003 6:27 PM
To: Nir Wittenberg
Subject: RE: QOS error message
Yes. IOS by default reserves 25% of the configured bandwidth for
overhead traffic. So if your bandwidth statement says 768k, you can
only reserve 576K.
-----Original Message-----
From: Nir Wittenberg [ mailto:nwittenberg@msncomm.com]
Sent: Thursday, October 16, 2003 5:21 PM
To: ccielab@groupstudy.com
Subject: QOS error message
Anyone seen this error message before? I tried putting on a service
policy to a map-class and got this:
I/f Serial0/0.17 DLCI 17 class voice requested bandwidth 512 (kbps)
Available o nly 384 (kbps)
This archive was generated by hypermail 2.1.4 : Mon Nov 24 2003 - 07:53:04 GMT-3