RE: ATM Questions and Lightstream LS100 configuration

From: istong@stong.org
Date: Thu Sep 25 2003 - 14:53:10 GMT-3

Hi Barney,

Here are some commands you can use to configure PVC's and SVC's on your
LS100.
This sets up pvc's and svc's between ports 0 and 2. You can expand it to
include port 4 if needed.

So for port 0 and vpi/vci 0/33 to port 2 vpi/vci 0/34 using oc3 interface:

pvc est 1 2 0 0 33 512 0 155 2 0 34 512 0 155

Then you can use the following to setup the interfaces:

set int 0 0 0 4 8 1 1 1
set int 2 0 0 4 8 1 1 1

Lastly if you want SVC's you would use the following commands (you can use
your own nsap address and mac address as desired):

route add 4701000000000000000000000000000c38a91100 nsap 2
route add 4701000000000000000000000000000c38a91401 nsap 2
route add 470100000000000000000000000060836cf84000 nsap 0
route add 470100000000000000000000000060836cf84101 nsap 0

Thanks,

Ian

Original Message:
-----------------
From: Barney Gaumer bagaumer@yahoo.com
Date: Wed, 24 Sep 2003 20:22:57 -0700 (PDT)
To: istong@stong.org, ccielab@groupstudy.com
Subject: RE: General ATM Questions

Would be much appreciated.

Here's some info from the LS100 if it helps?

atm#sh int
Line Inf_type Physical Layer Forum/ITU Vd VPI Vd VCI
LBO PLCP Scramble
  0 pri_UNI OC-3C(MMF) ATM Forum 4 8
Lo Direct ON
  2 pri_UNI OC-3C(MMF) ATM Forum 4 8
Lo Direct ON
  4 pri_UNI OC-3C(MMF) ATM Forum 4 8
Lo Direct ON

Local Information:
Host Name :atm
IP Address :192.168.250.4
Net Mask :255.255.255.0
Ether IP Address:0.0.0.0
Ether Net Mask :0.0.0.0
Router(Ether) :0.0.0.0
sysContact :
sysLocation :
ATM Address :01000000000000000000000000

NMS Information:
NMS Number 0 1
2 3
-----------+----------------+----------------+----------------+------------- 

---
IP Address :     0.0.0.0          0.0.0.0         
0.0.0.0          0.0.0.0
NetMask    :     0.0.0.0          0.0.0.0         
0.0.0.0          0.0.0.0
Gateway    :     0.0.0.0          0.0.0.0         
0.0.0.0          0.0.0.0
Line Number:        0                0               
0                0
VPI/VCI    :       0/   0           0/   0          
0/   0           0/   0
Community

Thanks,
Barney

--- Ian Stong <istong@stong.org> wrote:
> I can generate a basic config for you.  It's hard to
> send you one because your setup is unique and also the LS100 does
> not have a command like show running or write terminal to output the
> configuration.  You have to run commands for each piece of the setup to
> see how it is configured.
> 
> Ian
> 
> 
> -----Original Message-----
> From: nobody@groupstudy.com
> [mailto:nobody@groupstudy.com] On Behalf Of
> Barney Gaumer
> Sent: Wednesday, September 24, 2003 10:47 PM
> To: ccielab@groupstudy.com
> Subject: General ATM Questions
> 
> Can anyone tell me where I might find sample configs
> for a LS100 for Basic PVC/SVC setup.
> 
> The ATM hosts are 7505's w/1 AIP controller each.
> 
> I'm an ATM newb (never have had it in my
> environment)
> so I need as much help as I can get.
> 
> Thanks,
> Barney
> 
> 
> __________________________________
> Do you Yahoo!?
> Yahoo! SiteBuilder - Free, easy-to-use web site
> design software
> http://sitebuilder.yahoo.com
> 
> ***Get your CCIE and a FREE vacation:
> Shop.GroupStudy.com***
>

This archive was generated by hypermail 2.1.4 : Wed Oct 01 2003 - 07:24:37 GMT-3