From: miken (miken@sisna.com)
Date: Wed Sep 10 2003 - 13:53:03 GMT-3
Add the following to router 4:
interface Serial0
frame-relay map clns broadcast
You do not need to enable clns routing for this to work.
Thanks,
Mike N
----- Original Message -----
From: <oleg@chubb.com>
To: <ccielab@groupstudy.com>; <youshungang@hotmail.com>
Sent: Wednesday, September 10, 2003 6:45 AM
Subject: Re: isis neighbor adj problem
> If I may suggest another solution - Try to configure a tunnel between the
> mismatched ISIS interfaces.
>
>
> Oleg
>
>
>
>
>
> SN K38U
> <youshungang@hotm To:
ccielab@groupstudy.com
> ail.com> cc:
> Sent by: Subject: isis neighbor adj
problem
> nobody@groupstudy
> .com
>
>
> 09/07/2003 02:27
> AM
> Please respond to
> SN K38U
>
>
>
>
>
>
> Hi group#,when I worked on a lab recently,I encountered a problem about
> isis neighbor adj.
> Here is my topology:
> r3-s1--(frame-relay)--s0-r4-| e0
> |
> s0
>
> below is the detailed config:
>
> r3:
> interface Serial0
> no ip address
> encapsulation frame-relay
> frame-relay lmi-type ansi
> !
> interface Serial0.1 point-to-point
> ip address 10.13.1.2 255.255.0.0
> ip router isis
> frame-relay interface-dlci 301
> !
> interface Serial1
> ip address 10.34.1.1 255.255.0.0
> ip router isis
> encapsulation frame-relay
> frame-relay interface-dlci 304
> frame-relay lmi-type ansi
> !
> router isis
> net 01.3333.3333.3333.00
>
> r4:
> interface Ethernet0
> ip address 10.4.1.1 255.255.0.0
> ip router isis
> !
> interface Serial0
> ip address 10.34.1.2 255.255.0.0
> ip router isis
> encapsulation frame-relay
> frame-relay interface-dlci 403
> frame-relay lmi-type ansi
> !
> router isis
> net 01.4444.4444.4444.00
>
> I found that r3 and r4 cannot form isis neighbors.
> When i debug the isis neighbor adj,here is the output:
> r3#debug isis adj
> IS-IS Adjacency related packets debugging is on
> r3#
> 00:03:14: ISIS-Adj: Encapsulation failed for L1 LAN IIH on Serial1
> 00:03:15: ISIS-Adj: Encapsulation failed for L2 LAN IIH on Serial1
> on r4,there is the same problem.
>
> That confused me.The s0 should send serial IIH instead of LAN IIH since it
> is not a lan interface.Why the interface s0 does not behave normally? What
> cause this situation?
> Who can help out the problem? I wasted too much time on it.
> Please clarify it. Thanks a lot for any help!
>
> _________________________________________________________________
> OmSCJ@=gIOWn4s5D5gWSSJ<~O5M3!* MSN Hotmail!# http://www.hotmail.com
>
>
> _______________________________________________________________________
> You are subscribed to the GroupStudy.com CCIE R&S Discussion Group.
>
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
>
>
> _______________________________________________________________________
> You are subscribed to the GroupStudy.com CCIE R&S Discussion Group.
>
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
This archive was generated by hypermail 2.1.4 : Wed Oct 01 2003 - 07:24:25 GMT-3