From: John Matijevic (matijevi@bellsouth.net)
Date: Sat Aug 16 2003 - 15:29:23 GMT-3
Seong,
Lets forget about the router at the moment, and focus on changing the mtu on
the switch. The vlan mtu is 1518 vlan 10 correct? We want to change this to
1500.
When you change mtu on switch do not do the following:
int vlan 3
mtu 1518,
you need to do the following:
vlan 3 or whichever vlan
mtu 1500
try this and please post results.
Sincerely,
Matijevic
----- Original Message -----
From: "seonghui" <seonghui@vads.com>
To: "'John Matijevic'" <matijevi@bellsouth.net>; <ccielab@groupstudy.com>
Sent: Saturday, August 16, 2003 2:23 PM
Subject: RE: cat3550 cannot establish ospf nei with router/s
> Hi Matijevic,
>
> I don't believe u can change that, anyway below is what i've tried.
>
> conf t
> Enter configuration commands, one per line. End with CNTL/Z.
> r1(config)#int fas0/0
> r1(config-if)#mtu ?
> <64-18000> MTU size in bytes
> r3(config-if)#mtu 1518
> % Interface FastEthernet0/0 does not support user settable mtu.
>
> sw1(config)#int vlan 3
> sw1(config-if)#mtu 1500
> ^
> % Invalid input detected at '^' marker.
>
> I believe there is no command to set MTU size under switch int vlan and
> also, router doesn't allow u 2 change it.
>
> p/s: i hv not been sleeping for more than 20 hours...maybe shall take a
> short break and start afresh tomorrow morning.
>
> regards - SH
>
>
> -----Original Message-----
> From: John Matijevic [mailto:matijevi@bellsouth.net]
> Sent: Sunday, August 17, 2003 2:10 AM
> To: seonghui; ccielab@groupstudy.com
> Subject: Re: cat3550 cannot establish ospf nei with router/s
>
>
> Seong,
> On Switch enter:
> vlan 10
> mtu 1500
> or you can go to other router,
> int fa0/0
> and set mtu from interface
> Please post results,
> Sincerely,
> Matijevic
> ----- Original Message -----
> From: "seonghui" <seonghui@vads.com>
> To: "'John Matijevic'" <matijevi@bellsouth.net>; <ccielab@groupstudy.com>
> Sent: Saturday, August 16, 2003 2:05 PM
> Subject: RE: cat3550 cannot establish ospf nei with router/s
>
>
> > Hi Matijevic,
> >
> > MTU on router int fa0/0 is of course 1500 while MTU on vlan 10 is 1518.
I
> > tried changing them but router doesn't allow me to do so.
> >
> > any clue?
> >
> > regards - SH
> >
> > -----Original Message-----
> > From: John Matijevic [mailto:matijevi@bellsouth.net]
> > Sent: Sunday, August 17, 2003 1:55 AM
> > To: seonghui; ccielab@groupstudy.com
> > Subject: Re: cat3550 cannot establish ospf nei with router/s
> >
> >
> > Hello Seong,
> > Please check the mtu on the interface on the vlan interface as well as
the
> > interface on the router to make sure that the mtu is the same. ex. sh ip
> int
> > e0, or sh ip int vlan 20.
> > Please post results.
> > Sincerely,
> > Matijevic
> > ----- Original Message -----
> > From: "seonghui" <seonghui@vads.com>
> > To: "'John Matijevic'" <matijevi@bellsouth.net>;
<ccielab@groupstudy.com>
> > Sent: Saturday, August 16, 2003 1:42 PM
> > Subject: RE: cat3550 cannot establish ospf nei with router/s
> >
> >
> > > Hi Matijevic,
> > >
> > > I tried that earlier, but the result is the same.
> > >
> > > regards - SH
> > >
> > > -----Original Message-----
> > > From: John Matijevic [mailto:matijevi@bellsouth.net]
> > > Sent: Sunday, August 17, 2003 1:36 AM
> > > To: seonghui; ccielab@groupstudy.com
> > > Subject: Re: cat3550 cannot establish ospf nei with router/s
> > >
> > >
> > > Hello Seong,
> > > Could you try putting ip ospf priority 0 under vlan interface on
switch.
> > > Please post results.
> > > Sincerely,
> > > Matijevic
> > > ----- Original Message -----
> > > From: "seonghui" <seonghui@vads.com>
> > > To: <ccielab@groupstudy.com>
> > > Sent: Saturday, August 16, 2003 1:00 PM
> > > Subject: cat3550 cannot establish ospf nei with router/s
> > >
> > >
> > > > Hi group,
> > > >
> > > > I have been 'haunted' by this problem for the past two days. Here
the
> > > > problem goes...
> > > >
> > > > I have a router conneted to a Cat3550. router fa0/0 (ip address
> > > > 10.10.10.1/24) is connected to port fas0/1 (vlan 10) on cat3550. I
> would
> > > > like cat3550 to establish ospf neighbour with the router and hence,
I
> > > > created an Interface vlan 10 with ip address 10.10.10.2/24. However,
> the
> > > > router and the cat3550 just cannot form adjacency. Below is the
debug
> > > > message:
> > > >
> > > > 07:28:30: OSPF: rcv. v:2 t:1 l:48 rid:10.10.10.1 aid:0.0.0.10
chk:7E15
> > > aut:0
> > > > auk: from Vlan10
> > > > 07:28:30: OSPF: Rcv hello from 10.10.10.1 area 11 from Vlan10
> 10.10.10.2
> > > > 07:28:30: OSPF: End of hello processing
> > > > 07:28:31: OSPF: rcv. v:2 t:2 l:32 rid:10.10.10.1 aid:0.0.0.10
chk:21B2
> > > aut:0
> > > > auk: from Vlan10
> > > > 07:28:31: OSPF: Rcv DBD from 10.10.10.1 on Vlan10 seq 0x2D3 opt 0x42
> > flag
> > > > 0x7 len 32 mtu 1500 state EXSTART
> > > > 07:28:31: OSPF: First DBD and we are not SLAVE
> > > > 07:28:31: OSPF: Retransmitting DBD to 10.10.10.1 on Vlan10
> > > > 07:28:31: OSPF: 10.10.10.1 address 10.10.10.2 on Vlan10 is dead,
state
> > > DOWN
> > > > 07:28:31: %OSPF-5-ADJCHG: Process 1, Nbr 10.10.10.1 on Vlan10 from
> > EXSTART
> > > > to DOWN, Neighb or Down: Too many DBD retransmitions
> > > > 07:28:31: OSPF: Neighbor change Event on interface Vlan10
> > > > 07:28:36: OSPF: Rcv DBD from 10.10.10.1 on Vlan10 seq 0x2D3 opt 0x42
> > flag
> > > > 0x7 len 32 mtu
> > > > 1500 state DOWN
> > > > 07:28:36: OSPF: Nbr state is less than INIT
> > > >
> > > > I tried running other routing protocol between the switch and the
> > router,
> > > it
> > > > worked fine. Can some body please tell me what's the problem with
> ospf?
> > > >
> > > > Thanks,
> > > > SH
> > > >
> > > >
> > > >
> _______________________________________________________________________
> > > > You are subscribed to the GroupStudy.com CCIE R&S Discussion Group.
> > > >
> > > > Subscription information may be found at:
> > > > http://www.groupstudy.com/list/CCIELab.html
> > >
> > >
> > >
This archive was generated by hypermail 2.1.4 : Tue Sep 02 2003 - 18:53:59 GMT-3