From: Tony Schaffran (groupstudy@cconlinelabs.com)
Date: Wed Aug 13 2003 - 18:27:09 GMT-3
After you issue the csim start command, you have about 15 seconds to issue a
command on the router that you are calling to verify that the call is going
through. That command is:
show voice port | include Operation State
That command is case sensitive. The output will show either UP (ringing) or
DORMANT (not ringing) for each voice port.
I hope this helps. It is better than trying to interpret the csim output.
Tony Schaffran
Network Analyst
CCIE #11071
CCNP, CCNA, CCDA
NNCDS, NNCSS, CNE, MCSE
http://www.cconlinelabs.com/
Your #1 choice for online cisco rack rentals.
-----Original Message-----
From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of yu
chunyan
Sent: Wednesday, August 13, 2003 2:18 PM
To: cash2001@swbell.net; kwchen@netvigator.com
Cc: ccielab@groupstudy.com
Subject: RE: Voice over IP testing
It is not a successful call. note you have the following line:
csim err csimDisconnected recvd DISC cid(38)
Bin.
>From: "Jason Cash" <cash2001@swbell.net>
>Reply-To: "Jason Cash" <cash2001@swbell.net>
>To: "'Chen Kwong Wai William'" <kwchen@netvigator.com>
>CC: <ccielab@groupstudy.com>
>Subject: RE: Voice over IP testing
>Date: Wed, 13 Aug 2003 09:29:58 -0500
>
>From my output, this is a successful call:
>
>Successful VoIP Test
>r6#csim start 3333
> csim: called number = 3333, loop count = 1 ping count = 0
> csim: loop = 1, failed = 1
> csim: call attempted = 1, setup failed = 1, tone failed = 0
>
>
>-----Original Message-----
>From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
>Chen
>Kwong Wai William
>Sent: Wednesday, August 13, 2003 8:37 AM
>To: ccielab@groupstudy.com
>
>Dear all,
>
> Anyone try to use the "csim start" command to test the Voice over IP
>test on remote rack?
>
> The following command shows a successful call or not? I have test the
>connectivity between R4 and R7.
>
>R7#csim start 4411
>csim: called number = 4411, loop count = 1 ping count = 0
>
>csim err csimDisconnected recvd DISC cid(38)
>csim: loop = 1, failed = 1
>csim: call attempted = 1, setup failed = 1, tone failed = 0
>
>R7#sh run | begin dial-peer
>dial-peer cor custom
>!
>!
>!
>dial-peer voice 10 pots
> destination-pattern 7711
> port 1/0/0
>!
>dial-peer voice 20 voip
> destination-pattern 4411
> session target ipv4:110.99.4.4
> codec g723r63
>!
>dial-peer voice 1 pots
> destination-pattern 7000
> port 1/0/0
>!
>dial-peer voice 2 pots
> preference 1
> destination-pattern 7000
> port 1/0/1
>!
>
>R4#sh run | begin dial-peer
>dial-peer cor custom
>!
>!
>!
>dial-peer voice 10 pots
> destination-pattern 4411
> port 1/0/0
>!
>dial-peer voice 20 voip
> destination-pattern 7711
> session target ipv4:110.99.7.7
> codec g723r63
>!
>
>Best Regards,
>William Chen
>
>
>_______________________________________________________________________
>You are subscribed to the GroupStudy.com CCIE R&S Discussion Group.
>
>Subscription information may be found at:
>http://www.groupstudy.com/list/CCIELab.html
>
>
>_______________________________________________________________________
>You are subscribed to the GroupStudy.com CCIE R&S Discussion Group.
>
>Subscription information may be found at:
>http://www.groupstudy.com/list/CCIELab.html
This archive was generated by hypermail 2.1.4 : Tue Sep 02 2003 - 18:53:58 GMT-3