From: John Matijevic (matijevi@bellsouth.net)
Date: Tue Jul 08 2003 - 23:44:25 GMT-3
Thanks Tim,
I tried both commands but I am still getting the message.
Sincerely,
Matijevic
----- Original Message -----
From: "Snow, Tim" <timothy.snow@eds.com>
To: "'John Matijevic'" <matijevi@bellsouth.net>; <ccielab@groupstudy.com>
Sent: Tuesday, July 08, 2003 10:26 PM
Subject: RE: mismatch area in header
> I seem to have a faint memory of this type of issue happening with Frame
> Relay Inverse arp automagically mapping addresses that I didn't want
mapped.
>
>
> Which is why I usually turn on "no arp frame", "no frame inverse-arp"
always
> now. Take a look at that and see if that could be causing any issues.
>
> Tim
>
>
> -----Original Message-----
> From: John Matijevic [mailto:matijevi@bellsouth.net]
> Sent: Tuesday, July 08, 2003 10:12 PM
> To: John Matijevic; ccielab@groupstudy.com
> Subject: Re: mismatch area in header
>
>
> Hello Team,
> Still working on this....
> Here are configs so you can have a better idea of whats going on, again
> adjacencies are established, and i can ping across network.
> Sincerely,
> Matijevic
> r2#wr t
> Building configuration...
>
> Current configuration : 1415 bytes
> !
> version 12.1
> no service single-slot-reload-enable
> service timestamps debug uptime
> service timestamps log uptime
> no service password-encryption
> !
> hostname r2
> !
> logging rate-limit console 10 except errors
> !
> ip subnet-zero
> no ip finger
> !
> cns event-service server
> !
> !
> !
> !
> !
> interface Loopback0
> description management-loopback-interface
> ip address 172.16.102.1 255.255.255.255
> !
> interface Ethernet0
> ip address 172.16.20.2 255.255.255.0
> !
> interface Serial0
> ip address 172.16.123.2 255.255.255.0
> encapsulation frame-relay
> ip ospf network non-broadcast
> ip ospf priority 0
> frame-relay map ip 172.16.123.1 201 broadcast
> frame-relay map ip 172.16.123.2 201 broadcast
> frame-relay map ip 172.16.123.3 201 broadcast
> frame-relay lmi-type ansi
> !
> interface Serial1
> no ip address
> shutdown
> !
> interface BRI0
> no ip address
> shutdown
> !
> router ospf 1
> router-id 172.16.102.1
> log-adjacency-changes
> summary-address 172.16.50.0 255.255.255.0
> redistribute rip subnets route-map rip2ospf
> network 172.16.102.1 0.0.0.0 area 20
> network 172.16.123.0 0.0.0.255 area 0
> !
> router rip
> redistribute ospf 1 metric 2
> passive-interface default
> no passive-interface Ethernet0
> network 172.16.0.0
> !
> ip kerberos source-interface any
> ip classless
> no ip http server
> !
> access-list 1 permit 172.16.20.0 0.0.0.255
> route-map rip2ospf permit 10
> match ip address 1
> !
> !
> !
> line con 0
> transport input none
> line aux 0
> line vty 0 4
> login
> !
> end
>
> r2#
> comm-server#1
> [Resuming connection 1 to r1 ... ]
>
>
>
>
> r1>en
> r1#wr t
> Building configuration...
>
> Current configuration : 1396 bytes
> !
> version 12.1
> no service single-slot-reload-enable
> service timestamps debug uptime
> service timestamps log uptime
> no service password-encryption
> !
> hostname r1
> !
> logging rate-limit console 10 except errors
> !
> ip subnet-zero
> no ip finger
> !
> cns event-service server
> !
> !
> !
> !
> !
> interface Loopback0
> description loopback-management-interface
> ip address 172.16.101.1 255.255.255.255
> !
> interface Ethernet0
> no ip address
> shutdown
> !
> interface Serial0
> no ip address
> encapsulation frame-relay
> no fair-queue
> frame-relay lmi-type ansi
> !
> interface Serial0.1 multipoint
> ip address 172.16.123.1 255.255.255.0
> ip ospf network non-broadcast
> frame-relay map ip 172.16.123.1 102 broadcast
> frame-relay map ip 172.16.123.2 102 broadcast
> frame-relay map ip 172.16.123.3 103 broadcast
> no frame-relay inverse-arp
> !
> interface Serial0.2 point-to-point
> ip address 172.16.14.1 255.255.255.0
> ip ospf network point-to-point
> frame-relay interface-dlci 104
> !
> interface Serial1
> no ip address
> shutdown
> !
> interface BRI0
> no ip address
> shutdown
> !
> router ospf 1
> router-id 172.16.101.1
> log-adjacency-changes
> network 172.16.14.0 0.0.0.255 area 14
> network 172.16.101.1 0.0.0.0 area 10
> network 172.16.123.0 0.0.0.255 area 0
> neighbor 172.16.123.3
> neighbor 172.16.123.2
> !
> ip kerberos source-interface any
> ip classless
> no ip http server
> !
> !
> !
> line con 0
> transport input none
> line aux 0
> line vty 0 4
> login
> !
> end
>
> r1#
> comm-server#4
> [Resuming connection 4 to r4 ... ]
>
>
>
> r4>en
> r4#wr t
> Building configuration...
>
> Current configuration : 1211 bytes
> !
> version 12.1
> no service single-slot-reload-enable
> service timestamps debug uptime
> service timestamps log uptime
> no service password-encryption
> !
> hostname r4
> !
> !
> !
> !
> !
> !
> ip subnet-zero
> !
> ip audit notify log
> ip audit po max-events 100
> !
> !
> !
> !
> voice-port 1/0/0
> !
> voice-port 1/0/1
> !
> !
> !
> !
> interface Loopback0
> description management-loopback-interface
> ip address 172.16.104.1 255.255.255.255
> !
> interface Loopback1
> ip address 4.4.4.4 255.255.255.0
> !
> interface FastEthernet0/0
> ip address 172.16.34.4 255.255.255.0
> duplex auto
> speed auto
> !
> interface Serial0/0
> ip address 172.16.14.4 255.255.255.0
> encapsulation frame-relay
> ip ospf network point-to-point
> frame-relay map ip 172.16.14.1 401 broadcast
> frame-relay map ip 172.16.14.4 401 broadcast
> frame-relay lmi-type ansi
> !
> interface Serial0/1
> no ip address
> shutdown
> !
> router ospf 1
> router-id 172.16.104.1
> log-adjacency-changes
> redistribute rip subnets
> network 172.16.14.0 0.0.0.255 area 14
> !
> router rip
> version 2
> redistribute ospf 1 metric 2
> passive-interface default
> no passive-interface FastEthernet0/0
> network 4.0.0.0
> network 172.16.0.0
> no auto-summary
> !
> ip classless
> ip http server
> !
> !
> !
> !
> line con 0
> line aux 0
> line vty 0 4
> login
> !
> end
>
> r4#
> ----- Original Message -----
> From: "John Matijevic" <matijevi@bellsouth.net>
> To: <ccielab@groupstudy.com>
> Sent: Tuesday, July 08, 2003 9:42 PM
> Subject: mismatch area in header
>
>
> > Hello Team,
> > I have the following scenerio:
> > I have area 0 and area 14,
> > R1, R2 and R3 is in Area 0
> > R1 and R4 area in area 14
> > I can establish adjacencies fine.
> > But for some reason when I turn on deb ip ospf adj,
> > I get the following:
> > mismatch area 0.0.0.14 in the header,
> > Again, I can ping and form adjacencys, everything looks ok, but I want
to
> > resove this mismatch message I keep getting on R2, and R3,
> > Any assistance would be greatly appreciated!
> > Sincerely,
> > Matijevic
> >
> >
> > _______________________________________________________________________
> > You are subscribed to the GroupStudy.com CCIE R&S Discussion Group.
> >
> > Subscription information may be found at:
> > http://www.groupstudy.com/list/CCIELab.html
>
>
> _______________________________________________________________________
> You are subscribed to the GroupStudy.com CCIE R&S Discussion Group.
>
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
>
>
> _______________________________________________________________________
> You are subscribed to the GroupStudy.com CCIE R&S Discussion Group.
>
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
This archive was generated by hypermail 2.1.4 : Wed Aug 06 2003 - 06:52:29 GMT-3