From: Lin Xiaodong (Linxiaodong@21Vianet.com)
Date: Tue May 27 2003 - 23:37:17 GMT-3
thanks for your reply!
i tried to "no atm arp-ser self" but when i "show atm svc",there's no
output(output is empty and no svc),what's matter
-----e e' i.d;6-----
ed;6d::: Hossam Mahmoud [mailto:sam6626@yahoo.com]
eif6i4: 2003e945f 28f% 0:48
f6d;6d::: Lin Xiaodong; frank@buff-net.com
f
i: ccielab@groupstudy.com
d8;i": Re: ATM SVC
Lin and Frank,
As far as i know (Theory readings only) when you use classical ip (ARP
servers) mode you do't need to do any ip-svc mapping.
Using the ARP server all clients should be able to do ARP resolutions
for SVCs dynamically.
If my understanding is not contradicting with anything in yr scenario
then u better remvoe the SVC map command. And try without it.
Try pinging 172.16.1.2.
If it did't work then you better change the ip add. of yr ATM interface
to 192.168.1.1.
And then tyr pinging to 192.168.1.2
Or check with ATM BB administrator (if it is not yrself).
One last thing the out of the show command you are using really proofs
that the ARP server is working fine.
Waiting for yr feedback
Thanks
SAM
Lin Xiaodong <Linxiaodong@21Vianet.com> wrote:
I've seen the state: up and normal from command "show atm ilmi-st", and
got
the prefix from the other end. but the remote end's ip add is shown
"peer
ip add 192.168.1.2".
why, what's matter? why is it not "172.16.1.2", maybe 172.16.1.2 is sec
address, is it possible? I still cannot ping the other end :(
----- Original Message -----
From: "Frank B" < frank@buff-net.com >
To: "'Lin Xiaodong'" < Linxiaodong@21Vianet.com
>
Cc: < ccielab@groupstudy.com >
Sent: Friday, May 23, 2003 4:58 PM
Subject: RE: ATM SVC
> Where you have the svc nsap below, ensure you place the nsap from the
> router at the other end of your svc.
>
> You can verify it's working by using show atm ilmi-status
>
> You should see ilmi state: UpandNormal
> And after the registered esi address it should say (confirmed)
>
> Frank
>
> -----Original Message-----
> From: nobody@groupstudy.com
[mailto:nobody@groupstudy.com] On Behalf Of
> Lin Xiaodong
> Sent: Thursday, May 22, 2003 7:47 PM
> To: ccielab@groupstudy.com
> Subject: ATM SVC
>
> hi boddies,
> I config the atm svc as following but why i cannot always ping the
> remote end successfully ?
> maybe somewhere is wrong ? who can help me ? my config as follows
>
> int atm 2/0
> ip add 172.16.1.1 255.255.255.0
> atm esi-add xxxx.xxxx.xxxx.00
> pvc 0/16 ilmi
> !
> pvc 0/5 qusaal
> !
> atm ilmi-keepalive
> !
> atm arp-server self
> !
> svc nsap xx.xxxx.xxxx.xxxx.xxxx.xxxx.xxxx.xxxx.xxxx.xxxx.00
> proto ip 172.16.1.2 bro
> enc aal5snap
> !
>
> thanks in advance
_____
Do you Yahoo!?
The New
<http://us.rd.yahoo.com/search/mailsig/*http://search.yahoo.com> Yahoo!
Search - Faster. Easier. Bingo.
This archive was generated by hypermail 2.1.4 : Mon Jun 02 2003 - 15:13:49 GMT-3