RE: IPexpert Section 13 Qos (CustomQueing) Exercise 6

From: Ouellette, Tim (tim.ouellette@eds.com)
Date: Thu May 01 2003 - 20:24:24 GMT-3

After reading your email, it appears that you were asking what those two
values meant and since I have no idea that you already knew that, I answered
the question.

As far as queue 5 and 6, i'm thinking it's probably a typo...

Tim

-----Original Message-----
From: Oliver Ziltener [mailto:ziltener@netcloud.ch]
Sent: Thursday, May 01, 2003 8:50 AM
To: Ouellette, Tim
Cc: ccielab@groupstudy.com
Subject: AW: IPexpert Section 13 Qos (CustomQueing) Exercise 6

Thanks Tim
Im allready know that-of course. I wanna know the limit number 1500 and
byte-count number 1024 in queue 5 and 6. Everything is related to exercise
6,
because to queue 5 and 6 there are not information about limit and
byte-count
and both number are not default. So why they put this numbers to queue 5 and
6.
 
Thanks
Oliver

        -----UrsprCB<ngliche Nachricht-----
        Von: Ouellette, Tim
        Gesendet: Do 01.05.2003 11:45
        An: Oliver Ziltener
        Cc: 'ccielab@groupstudy.com'
        Betreff: RE: IPexpert Section 13 Qos (CustomQueing) Exercise 6
        
        

        I did a search on cisco.com for "queue-list" clicked the first
link,
        scrolled 1/4 of a page and found the following
        
        queue-list list-number queue queue-number limit limit-number
Specifies the
        maximum number of packets allowed in each of the custom queues. The
        limit-number argument specifies the number of packets that can be
enqueued
        at any one time. The range is 0 to 32767.
        (my understanding is this is the queue-depth, or the amount of
packets
        allowed to sit in memory buffers while the router is transmiting)
        
        queue-list list-number queue queue-number byte-count
byte-count-number
        Designates the average number of bytes forwarded per queue. The
        byte-count-number argument specifies the average number of bytes the
system
        allows to be delivered from a given queue during a particular cycle.
        (this is the amount of bytes that this queue is allowed to send
during an
        interval, this is the main point for custom queuing, set the limit
to
each
        queue size so each queue gets a fair share)
        
        
http://www.cisco.com/en/US/partner/products/sw/iosswrel/ps1831/products_conf
        iguration_guide_chapter09186a00800c60d4.html
        
        Tim
        
        
        
        
        -----Original Message-----
        From: Oliver Ziltener [mailto:ziltener@netcloud.ch]
        Sent: Thursday, May 01, 2003 4:22 AM
        To: ccielab@groupstudy.com
        Subject: IPexpert Section 13 Qos (CustomQueing) Exercise 6
        
        
        Hello
        
        can anybody explain the last two line of this exercise nr.6.
        I can't see any point to set up this packet limit and this
byte-count!
        
        queue-list 1 protocol ip 1 tcp smtp
        queue-list 1 protocol ip 2 tcp tacacs
        queue-list 1 protocol ip 2 tcp domain
        queue-list 1 protocol ip 2 udp domain
        queue-list 1 protocol ip 3 tcp www
        queue-list 1 protocol cdp 4
        queue-list 1 protocol ip 5 lt 768
        queue-list 1 protocol ip 5 gt 767
        queue-list 1 queue 1 limit 1000
        queue-list 1 queue 2 byte-count 4000
        queue-list 1 queue 3 limit 10000
        queue-list 1 queue 4 byte-count 500
        queue-list 1 queue 5 limit 1500 <<<<<<<<<<<<<<<<?????
        queue-list 1 queue 6 byte-count 1024 <<<<<<<<<<<<?????
        
        
        thanks
        Oliver

This archive was generated by hypermail 2.1.4 : Mon Jun 02 2003 - 15:13:35 GMT-3