From: Silvio Nunes (silvio_98@hotmail.com)
Date: Mon Apr 28 2003 - 18:05:52 GMT-3
Hi Tom,
This configuration doesn4t works with "shutdown command" (in the interface).
Try disconnect the cable and try again..
Silvio.
>From: Tom Young <gitsyoung@yahoo.co.jp>
>Reply-To: Tom Young <gitsyoung@yahoo.co.jp>
>To: ccielab@groupstudy.com
>Subject: isdn backup
>Date: Tue, 29 Apr 2003 03:28:54 +0900 (JST)
>
>Hi, group
>
> I made a isdn backup for my s0.1. The isdn is active, but
>if I set the backup int b0 command, the b0 into the
>standby status.And don't active forever, even I shutdown
>the s0.1, maybe I couldn't use the callback in the same
>time?
>
>
>r5#sh dia
>!
>!
>interface Loopback0
> ip address 137.50.50.1 255.255.255.0
>!
>interface Loopback10
> ip address 5.5.5.5 255.255.255.0
>!
>interface Ethernet0
> no ip address
> ip ospf priority 0
> shutdown
>!
>interface Serial0
> no ip address
> encapsulation frame-relay
> frame-relay lmi-type ansi
>!
>interface Serial0.1 multipoint
> bandwidth 64
> backup delay 2 2
> backup interface BRI0
> ip address 172.168.100.5 255.255.255.0
> ip ospf priority 200
> frame-relay map ip 172.168.100.3 503 broadcast
> frame-relay map ip 172.168.100.6 506 broadcast
> no frame-relay inverse-arp
>!
>interface Serial1
> no ip address
> encapsulation frame-relay
> no ip route-cache
> no ip mroute-cache
> frame-relay lmi-type ansi
>!
>interface Serial1.1 multipoint
> ip address 172.168.200.5 255.255.255.0
> no ip route-cache
> no ip mroute-cache
> frame-relay map ip 172.168.200.4 504 broadcast
> frame-relay map ip 172.168.200.8 508 broadcast
> no frame-relay inverse-arp
>!
>interface BRI0
> ip address 65.1.1.1 255.255.255.0
> encapsulation ppp
> ip ospf demand-circuit
> dialer map ip 65.1.1.2 name r6 class call broadcast 2002
> dialer-group 1
> isdn switch-type basic-net3
> ppp callback accept
> ppp authentication chap callin
>!
>router ospf 1
> log-adjacency-changes
> area 0 range 65.0.0.0 255.0.0.0
> redistribute igrp 1 metric 200 metric-type 1 subnets
> network 65.1.1.1 0.0.0.0 area 0
> network 172.168.100.5 0.0.0.0 area 0
> neighbor 172.168.100.6 priority 1
> neighbor 172.168.100.3 priority 1
> default-information originate always metric-type 1
>!
>router igrp 1
> timers basic 5 15 0 30
> redistribute ospf 1
> passive-interface Serial0.1
> network 172.168.0.0
> default-metric 64 100 255 1 1500
>!
>router bgp 5
> bgp log-neighbor-changes
> network 5.5.5.0 mask 255.255.255.0
> neighbor 172.168.100.3 remote-as 3
> neighbor 172.168.100.6 remote-as 6
> neighbor 172.168.200.4 remote-as 4
>!
>ip kerberos source-interface any
>ip classless
>no ip http server
>!
>!
>map-class dialer call
> dialer callback-server username
>dialer-list 1 protocol ip permit
>!
>alias exec sir sh ip route
>alias exec cir clear ip route *
>!
>line con 0
> transport input none
>line aux 0
>line vty 0 4
> privilege level 15
> login
>!
>end
>
>When I show the dialer , I found the interface was down.
>
>
>
>BRI0 - dialer type = ISDN
>
>Dial String Successes Failures Last DNIS Last
>status
>2002 33 1 00:06:12
>successful
>0 incoming call(s) have been screened.
>0 incoming call(s) rejected for callback.
>
>BRI0:1 - dialer type = ISDN
>Idle timer (120 secs), Fast idle timer (20 secs)
>Wait for carrier (30 secs), Re-enable (15 secs)
>Dialer state is shutdown
>
>BRI0:2 - dialer type = ISDN
>Idle timer (120 secs), Fast idle timer (20 secs)
>Wait for carrier (30 secs), Re-enable (15 secs)
>Dialer state is shutdown
>r5#
>
>
>Where the problem ?
>
>
>Thanks alot
>
>__________________________________________________
>Do You Yahoo!?
>Yahoo! BB is Broadband by Yahoo! http://bb.yahoo.co.jp/
This archive was generated by hypermail 2.1.4 : Thu May 01 2003 - 13:36:09 GMT-3