From: CCIE FUN (ccieexam2002@yahoo.com)
Date: Fri Mar 07 2003 - 21:10:30 GMT-3
the default ospf network type on OSPF multipoint or
phsical interface is non-broadcast.
i think you could used network types of
point-to-multipoint on all the routers and still
suffice the requirements.
--- Tony Schaffran <tschaffran@cconlinelabs.com>
wrote:
> I seem to recall, that did not work on the Frame
> Relay network without the
> "non-broadcast". I could be wrong. What is the
> default?
>
>
>
> Tony Schaffran
> Network Analyst
> CCIE #11071
> CCNP, CCNA, CCDA,
> NNCSS, NNCDS, CNE, MCSE
>
> www.cconlinelabs.com
> "Your #1 choice for Cisco rack rentals."
>
>
> ----- Original Message -----
> From: "c ," <ccie1@hotmail.com>
> To: <tschaffran@cconlinelabs.com>;
> <scotsman@rediffmail.com>;
> <ccielab@groupstudy.com>
> Sent: Friday, March 07, 2003 8:36 AM
> Subject: Re: OSPF on NBMA Networks
>
>
> >
> >
> > What about ip ospf network point-multipoint?
> >
> > The quwstion didnt say you couldnt use those.
> >
> >
> >
> >
> >
> > >From: "Tony Schaffran"
> <tschaffran@cconlinelabs.com>
> > >Reply-To: "Tony Schaffran"
> <tschaffran@cconlinelabs.com>
> > >To: "Scot Peter" <scotsman@rediffmail.com>,
> <ccielab@groupstudy.com>
> > >Subject: Re: OSPF on NBMA Networks
> > >Date: Thu, 6 Mar 2003 11:15:47 -0800
> > >
> > >This is a perfect example of not reading too deep
> into it. Keep it
> simple.
> > >If the scenario tells you "Don't configure
> Network type Broadcast or
> > >non-broadcast" and you can use neighbor
> statements, why not just use
> > >neighbor statements?
> > >
> > >Remember, you don't get extra points for
> creativity.
> > >
> > >
> > >
> > >Tony Schaffran
> > >Network Analyst
> > >CCIE #11071
> > >CCNP, CCNA, CCDA,
> > >NNCSS, NNCDS, CNE, MCSE
> > >
> > >www.cconlinelabs.com
> > >"Your #1 choice for Cisco rack rentals."
> > >
> > >
> > >----- Original Message -----
> > >From: "Tony Schaffran"
> <tschaffran@cconlinelabs.com>
> > >To: "Scot Peter" <scotsman@rediffmail.com>;
> <ccielab@groupstudy.com>
> > >Sent: Thursday, March 06, 2003 10:36 AM
> > >Subject: Re: OSPF on NBMA Networks
> > >
> > >
> > > > It sounds like you just need the neighbor
> statements.
> > > >
> > > >
> > > >
> > > > Tony Schaffran
> > > > Network Analyst
> > > > CCIE #11071
> > > > CCNP, CCNA, CCDA,
> > > > NNCSS, NNCDS, CNE, MCSE
> > > >
> > > > www.cconlinelabs.com
> > > > "Your #1 choice for Cisco rack rentals."
> > > >
> > > >
> > > > ----- Original Message -----
> > > > From: "Scot Peter" <scotsman@rediffmail.com>
> > > > To: <ccielab@groupstudy.com>
> > > > Sent: Thursday, March 06, 2003 4:54 AM
> > > > Subject: OSPF on NBMA Networks
> > > >
> > > >
> > > > > Hello Group
> > > > >
> > > > > If we need to configure OSPF on a Multipoint
> interface with the
> > > > > following condition,
> > > > > - R1 should use Multipoint interfaces,
> > > > > - R2, R3 should not use subinterfaces,
> > > > > - All three routers should be in the same
> Network.
> > > > > - Don't configure Network type Broadcast or
> non-broadcast.
> > > > >
> > > > > R1
> > > > > / \
> > > > > R2 R3
> > > > >
> > > > > I am not sure about configuring "ip ospf
> network
> > > > > point-to-multipoint" (As the question
> mentions not to configure
> > > > > Non-broadcast) or do we need to configure
> using "neighbor"
> > > > > command? Please advice me on this.
> > > > >
> > > > > Regards
> > > > > Pet
> >
> >
> >
>
This archive was generated by hypermail 2.1.4 : Sat Apr 05 2003 - 08:51:34 GMT-3