From: Gery Pang (pang_gery@yahoo.com.hk)
Date: Sat Mar 01 2003 - 23:21:43 GMT-3
Thank you Hondo.
I have tried to make the dialer map statement both in the dialer interface
and the physical interface in the calling router, but not success.
R5-2621#ct
Enter configuration commands, one per line. End with CNTL/Z.
R5-2621(config)#int bri 0/0
R5-2621(config-if)#dialer map ip 172.16.5.0 name R6-3640 broad 5100
%Remove Dialer Profile Configuration first
R5-2621(config-if)#int dialer 0
R5-2621(config-if)#dialer map ip 172.16.5.0 name R6-3640 broad 5100
^
% Invalid input detected at '^' marker.
R5-2621(config-if)#
Am I doing something wrong?
Thank you.
Gery
----- Original Message -----
From: "OhioHondo" <ohiohondo@columbus.rr.com>
To: "Gery Pang" <pang_gery@yahoo.com.hk>; <ccielab@groupstudy.com>
Sent: Sunday, March 02, 2003 12:50 AM
Subject: RE: dialer watch and dialer profile
> Gery
>
> Make the idle-timeout on the calling side something other than 0. This
sets
> the time for the check that the dialer does to see if the watched routes
> returned. If the watched routes have returned the Dialer drops the link.
If
> the watched routes have not returned, the idle timer resets and the routes
> are not checked again until it times out again.
>
> I believe that you need dialer map statements on the calling side. These
map
> statements have to reference the "watched" routes otherwise the dialer
does
> not know what to check when the iidle timer times out.
>
> -----Original Message-----
> From: nobody@groupstudy.com [mailto:nobody@groupstudy.com]On Behalf Of
> Gery Pang
> Sent: Saturday, March 01, 2003 9:50 AM
> To: ccielab@groupstudy.com
> Subject: dialer watch and dialer profile
>
>
> Hi Group,
>
> I have a question using dialer watch with dialer profile.
>
> Here is the config:
>
> The calling router:
>
> interface BRI0/0
> no ip address
> encapsulation ppp
> dialer pool-member 1
> isdn switch-type basic-ni
> isdn spid1 5201 5200
> isdn spid2 5202 5200
> ppp authentication chap
> ppp multilink
>
> interface Dialer0
> ip address 172.16.224.5 255.255.255.0
> encapsulation ppp
> ip ospf demand-circuit
> dialer pool 1
> dialer remote-name R6-3640
> dialer watch-disable 10
> dialer string 5100
> dialer watch-group 10
> pulse-time 0
>
>
> The called router:
>
>
> interface BRI1/0
> no ip address
> encapsulation ppp
> ip ospf demand-circuit
> dialer pool-member 1
> isdn switch-type basic-ni
> isdn spid1 5101 5100
> isdn spid2 5102 5100
> no peer neighbor-route
> no cdp enable
> ppp authentication chap
> ppp multilink
>
> interface Dialer0
> ip address 172.16.224.6 255.255.255.0
> encapsulation ppp
> dialer pool 1
> dialer remote-name R5-2621
> dialer idle-timeout 0
> dialer string 5200
> dialer load-threshold 1 either
>
> The idle-timer on called side is 0 to prevent it from dropping the line.
But
> I
> found the calling side keep dropping the line when the idle timer pass and
> the
> line is up again because of dialer watch.
> If I set the idle timeout to 0, the line is not drop even the watched
route
> appear in the route table, even the watch-disable timer pass.
>
> The following is the sh dialer from the calling router, the routed route
is
> in
> the route table.
>
> R5-2621#sh dialer
>
> BRI0/0 - dialer type = ISDN
>
> Dial String Successes Failures Last DNIS Last status
> 0 incoming call(s) have been screened.
> 0 incoming call(s) rejected for callback.
>
> BRI0/0:1 - dialer type = ISDN
> Idle timer (never), Fast idle timer (20 secs)
> Wait for carrier (30 secs), Re-enable (15 secs)
> Dialer state is multilink member
> Interface bound to profile Di0
> Current call connected 00:29:04
> Connected to 5100 (R6-3640)
>
> BRI0/0:2 - dialer type = ISDN
> Idle timer (never), Fast idle timer (20 secs)
> Wait for carrier (30 secs), Re-enable (15 secs)
> Dialer state is data link layer up
> Dial reason: Dialing on watched route loss
> Interface bound to profile Di0
> Current call connected 00:29:04
> Connected to 5100 (R6-3640)
>
> Di0 - dialer type = DIALER PROFILE
> Idle timer (never), Fast idle timer (20 secs)
> Wait for carrier (30 secs), Re-enable (15 secs)
> Dialer state is data link layer up
> Number of active calls = 2
>
> Dial String Successes Failures Last DNIS Last status
> 5100 15 0 00:29:12 successful
Default
>
> Thank you.
>
> Gery
>
This archive was generated by hypermail 2.1.4 : Sat Apr 05 2003 - 08:51:30 GMT-3