From: Mohamed Nizam (torontocisco@yahoo.ca)
Date: Wed Feb 26 2003 - 04:02:42 GMT-3
Yes. You can configure one of the serial interface as terminating
FRame-relay interface. You can enter a frame relay statement & an IP Address
on that interface. If you can send the config , I can modify and send back
to you.
Thanks,
Mohamed Nizam,
A proud student of WinNET Harith.
----- Original Message -----
From: "sam" <sam@avtechusa.com>
To: "'Mohamed Nizam'" <torontocisco@yahoo.ca>
Cc: <ccielab@groupstudy.com>
Sent: Monday, February 24, 2003 5:26 PM
Subject: RE: Frame Relay
> Hi, all! I understand from the previous posts on this group that you can
> configure the frame relay switch to also perform layer 3 routing
> functions.
>
> I believe someone also mentioned that they use their frame-relay switch
> as a backbone router to inject routes into their topology.
>
> I have a 4000 series router configured as my frame-relay switch. It is
> running IOS v10. Will I be able to configure my 4000 as a BB router as
> well?
>
> The reason I ask is because I am away from home for a while and I do not
> have access to my router to configure it.
>
> Thanks for any input.
>
> Sam Sena
> Chief Microsoft Trainer
> MCT, MCSE, MCDBA, CCNP
> Avtech Technologies
>
> 4500 New Brunswick Ave
> Piscataway NJ
> (732) 424-8008 (o)
> (732) 424-7388 (f)
>
>
> -----Original Message-----
> From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
> Mohamed Nizam
> Sent: Monday, February 24, 2003 4:09 PM
> To: Cheng Qian
> Cc: Vijay S Jayaraman; Larry Letterman; Bobby; ccielab@groupstudy.com;
> nobody@groupstudy.com
> Subject: Re: Frame Relay
>
> You are correct.
>
> Harith.
>
> A proud student of WinNET Harith.
>
> ----- Original Message -----
> From: "Cheng Qian" <toqian@cisco.com>
> To: "Mohamed Nizam" <torontocisco@yahoo.ca>
> Cc: "Vijay S Jayaraman" <vjayaram@in.ibm.com>; "Larry Letterman"
> <lletterm@cisco.com>; "Bobby" <bobby1@ctimail3.com>;
> <ccielab@groupstudy.com>; <nobody@groupstudy.com>
> Sent: Monday, February 24, 2003 9:20 AM
> Subject: Re: Frame Relay
>
>
> > For your second way to setup, if you did not enable frame-relay
> switching
> > on R6, it won't allow you to configure it with frame-relay intfp-type
> dce.
> >
> >
> > At 08:17 AM 2/21/2003 -0500, Mohamed Nizam wrote:
> > >There are two kind of Frame relay set-up.
> > >
> > >1. Frame relay thorough a FR-Switch. R5------ s0- FR-S -s1----- R6.
> > > This is what we most of the time practice. The middle
> router
> is
> > >configured as FR- Switch. Usually we connect Cable's DCE side to
> FR-Sw.
> But
> > >it is not mandatory. If so the config of the switch will be
> > >
> > >frame switching
> > >
> > >int s0
> > > encap frame
> > > clock rate 56000
> > > frame intf-type dce
> > > frame route 506 int s 1 605
> > >
> > >int s1
> > > encap frame
> > > clock rate 56000
> > > frame intf-type dce
> > > frame route 605 int s 0 506
> > >
> > >
> > >2. Terminating Frame Relay . R5 -S1--------------------S0/0-R6
> > >
> > > No switch is between them. Then one side of the link should be
> frame
> > >intf-type dce. ( Cable DCE end , and thsi not necessary to be match.
> ) .
> > >Also both sides DLCI numbers can be same or different.
> > >
> > > R5
> > > interface Serial1
> > > ip address 200.100.2.1 255.255.255.0
> > > encapsulation frame-relay
> > > frame-relay map ip 200.100.2.2 102 broadcast
> > >
> > > R6
> > > interface Serial0/0
> > > ip address 200.100.2.2 255.255.255.0
> > > encapsulation frame-relay
> > > clockrate 64000
> > > frame intf-type dce
> > > frame-relay map ip 200.100.2.1 201 broadcast
> > >
> > >
> > >Thanks,
> > >
> > >Mohamed Nizam
> > >
> > >" A proud student of Harith"
> > >
> > >
> > >----- Original Message -----
> > >From: "Vijay S Jayaraman" <vjayaram@in.ibm.com>
> > >To: "Larry Letterman" <lletterm@cisco.com>
> > >Cc: "Bobby" <bobby1@ctimail3.com>; <ccielab@groupstudy.com>;
> > ><nobody@groupstudy.com>
> > >Sent: Friday, February 21, 2003 4:50 AM
> > >Subject: Re: Frame Relay
> > >
> > >
> > > > A frame relay back to back should work....if you enable "frame
> relay
> > > > switching" on the dce side, add the "clock-rate" command on the
> dce
> > > > interface, add "frame relay intf-type dce" to the dce end and have
> the
> > > > DLCIs at both the connecting interfaces....
> > > >
> > > > But I doubt whether you would ever have the oppurtunity to do this
> in
> an
> > > > actual lab because all the routers connect only through the frame
> relay
> > > > switch and you are not allowed to touch that.....
> > > >
> > > >
> > > > Regards,
> > > > Vijay.
> > > >
> > > >
> > > >
> > > >
> > > >
> > > > "Larry Letterman"
> > > > <lletterm@cisco.c To: "Bobby"
> > ><bobby1@ctimail3.com>, <ccielab@groupstudy.com>
> > > > om> cc:
> > > > Sent by: Subject: Re: Frame
> Relay
> > > > nobody@groupstudy
> > > > .com
> > > >
> > > >
> > > > 02/21/2003 01:02
> > > > PM
> > > > Please respond to
> > > > "Larry Letterman"
> > > >
> > > >
> > > >
> > > >
> > > >
> > > > I'd be surprised if your config works..which one is the DTE
> > > > and which is the DCE..
> > > > I have a frame switch setup in my lab which works..and the
> > > > frame switch uses frame relay
> > > > routing and DCE/Clock rate commands..
> > > >
> > > > Also the Lab as I understand it is already configured for
> > > > things like that..we should only have to configure the
> > > > routers that connect to each other..altho people have said
> > > > here and elsewhere that it might be in my interest
> > > > to know how to set up a frame switch...
> > > >
> > > > Larry Letterman
> > > > Network Engineer
> > > > Cisco Systems
> > > >
> > > >
> > > > ----- Original Message -----
> > > > From: "Bobby" <bobby1@ctimail3.com>
> > > > To: <ccielab@groupstudy.com>
> > > > Sent: Thursday, February 20, 2003 6:01 PM
> > > > Subject: Frame Relay
> > > >
> > > >
> > > > > Hi Friends,
> > > > >
> > > > > If in the lab we were asked to configure a back to back fr
> > > > connection
> > > > > whether the following config is ok :
> > > > >
> > > > > R5
> > > > > interface Serial1
> > > > > ip address 200.100.2.1 255.255.255.0
> > > > > encapsulation frame-relay
> > > > > no keepalive
> > > > > frame-relay map ip 200.100.2.2 102 broadcast
> > > > >
> > > > >
> > > > > R6
> > > > > interface Serial0/0
> > > > > ip address 200.100.2.2 255.255.255.0
> > > > > encapsulation frame-relay
> > > > > no keepalive
> > > > > clockrate 64000
> > > > > frame-relay map ip 200.100.2.1 102 broadcast
> > > > >
> > > > > I was told that they will not accept the above config. Is
> > > > there
> > > > > any other way do it.
> > > > >
> > > > > Thanks
> > >
> >
> >______________________________________________________________________
> > >Post your free ad now! http://personals.yahoo.ca
>
> ______________________________________________________________________
> Post your free ad now! http://personals.yahoo.ca
This archive was generated by hypermail 2.1.4 : Sat Mar 01 2003 - 11:06:36 GMT-3