From: Ong Boon Hui (ongbh@cet.st.com.sg)
Date: Fri Feb 14 2003 - 12:06:14 GMT-3
Hi,
Thx for the pointer.
Changed the configuration but still do not work. strange ..
See below ..
Enter configuration commands, one per line. End with CNTL/Z.
R8(config)#int atm 1/0
R8(config-if)#pvc 0/16 ilmi
R8(config-if-atm-vc)#^Z
R8#sh a
3d12h: %SYS-5-CONFIG_I: Configured from console by consoletm vc
VCD / Peak Avg/Min Burst
Interface Name VPI VCI Type Encaps SC Kbps Kbps Cells
Sts
1/0 1 0 5 PVC SAAL UBR 155000
UP
1/0 175 0 16 PVC ILMI UBR 155000
UP
R8#ping 101.1.1.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 101.1.1.1, timeout is 2 seconds:
.....
R8#sh atm ilmi-status
Interface : ATM1/0 Interface Type : Private UNI (User-side)
ILMI VCC : (0, 16) ILMI Keepalive : Enabled (5 Sec 4 Retries)
ILMI State: UpAndNormal
Peer IP Addr: 0.0.0.0
Peer MaxVPIbits: 2 Peer MaxVCIbits: 10
Active Prefix(s) :
39.0348.8001.bc90.0001.0152.d800
Debarros
----- Original Message -----
From: "sam" <sam@avtechusa.com>
To: "'Ong Boon Hui'" <ongbh@cet.st.com.sg>
Cc: <ccielab@groupstudy.com>
Sent: Friday, February 14, 2003 10:53 PM
Subject: RE: ATM help pls
> Correct me if I'm wrong, but do you need 'ilmi' after the pvc 0/16 ?
>
> RE:(watch wrap)
>
> http://www.cisco.com/univercd/cc/td/doc/product/software/ios121/121cgcr/
> wan_c/wcdatm.htm#1001470
>
> You must complete the tasks in the following sections to use SVCs:
> 1.Configuring Communication with the ILMI (Required)
> 2.Configuring the PVC that Performs SVC Call Setup (Required)
> 3.Configuring the NSAP Address (Required)
> 4.Creating an SVC (Required)
> .....
>
> 1. Configuring Communication with the ILMI
> In an SVC environment, you must configure a PVC for communication with
> the Integrated Local Management Interface (ILMI) so the router can
> receive SNMP traps and new network prefixes. The recommended vpi and vci
> values for the ILMI PVC are 0 and 16, respectively. To configure ILMI
> communication, use the following command in interface configuration
> mode:
>
>
> Command Purpose
> pvc [name] 0/16 ilmi Create an ILMI PVC on an ATM main interface.
>
>
> Sam Sena
> {Wah Lau Eh... I'm in New Jersey...}
>
>
> -----Original Message-----
> From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
> Ong Boon Hui
> Sent: Friday, February 14, 2003 9:25 AM
> To: ccielab@groupstudy.com
> Subject: ATM help pls
>
> Hi,
>
> need help pls, I cannot PING across the following routers with ATM
> interfaces
> :-
>
> Router 2
>
> interface ATM1/0
> ip address 101.1.1.2 255.255.255.0
> atm uni-version 3.1
> atm esi-address 222222222222.22
> atm ilmi-keepalive
> atm ilmi-pvc-discovery
> pvc 0/5 qsaal
> !
> pvc 0/16
> !
> !
> svc nsap 39.03488001BC9000010152D800.111111111111.11
> protocol ip 101.1.1.1 broadcast
>
>
>
> Router 1
>
> interface ATM4/0/0
> ip address 101.1.1.1 255.255.255.0
> atm esi-address 111111111111.11
> atm ilmi-keepalive
> atm ilmi-pvc-discovery
> pvc 0/5 qsaal
> !
> pvc 0/16
> !
> !
> svc toR8 nsap 39.03488001BC9000010152D800.222222222222.22
> protocol ip 101.1.1.2 broadcast
>
>
> Getting tired and a little crazy, any help or advice is appreciated.
>
>
> Debarros
This archive was generated by hypermail 2.1.4 : Sat Mar 01 2003 - 11:06:23 GMT-3