From: Joe Chang (changjoe@earthlink.net)
Date: Thu Dec 05 2002 - 13:07:06 GMT-3
Also, don't forget to configure "ip routing". It has to be done explicitly
on the 3500.
----- Original Message -----
From: "Imran" <imran@eccdxb.co.ae>
To: "'Rik Guyler '" <Rik@Guyler.net>; <ccielab@groupstudy.com>
Sent: Thursday, December 05, 2002 11:13 AM
Subject: RE: Question about Cat3550 with latest EMI IOS
> Hi Desmond,
>
> The vlan 10 in your case will be show line protocol down if you dont
assign
> the port router is connected to VLAN 10.We need atleast 1 port in
> vlan to make it up
> By default all the ports are in VLAN 1 that why its not working , you cant
> even ping 10.10.10.1 from your router.
> I tired this and it works , you need to add the port the router is
connected
> to VLAN 10.
>
> Folloiwng is a working config from my lab
>
> Router
> r8#sh runn int eth 0
> Building configuration...
>
> Current configuration : 62 bytes
> !
> interface Ethernet0
> ip address 11.1.1.2 255.255.255.0
> end
>
> r8#sh ip eigrp ne
> IP-EIGRP neighbors for process 1
> H Address Interface Hold Uptime SRTT RTO Q Seq
> Type
> (sec) (ms) Cnt Num
> 0 11.1.1.1 Et0 13 00:04:12 4 200 0 1
> r8#sh ip route
> Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
> D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
> N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
> E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
> i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter
> area
> * - candidate default, U - per-user static route, o - ODR
> P - periodic downloaded static route
>
> Gateway of last resort is not set
> C 10.1.1.0/24 is directly connected, Serial0
> 11.0.0.0/24 is subnetted, 1 subnets
> C 11.1.1.0 is directly connected, Ethernet0
> D 12.0.0.0/8 [90/409600] via 11.1.1.1, 00:04:13, Ethernet0
> r8#
>
>
> Switch
>
> 3550EMI#sh runn int fa0/10
> Building configuration...
>
> Current configuration : 76 bytes
> !
> interface FastEthernet0/10
> switchport access vlan 10
> no ip address
> end
>
> 3550EMI#
> 3550EMI#sh runn int vlan 10
> Building configuration...
>
> Current configuration : 59 bytes
> !
> interface Vlan10
> ip address 11.1.1.1 255.255.255.0
> end
>
> 3550EMI#
>
> 3550EMI#sh ip eigrp ne
> IP-EIGRP neighbors for process 1
> H Address Interface Hold Uptime SRTT RTO Q Seq
> Type
> (sec) (ms) Cnt Num
> 0 11.1.1.2 Vl10 11 00:05:39 1 3000 0 2
> 3550EMI#
>
>
> Thanks
>
> Imran
>
>
>
>
>
> -----Original Message-----
> From: Rik Guyler
> To: 'ccielab@groupstudy.com'
> Sent: 05/12/02 07:04 ?
> Subject: RE: Question about Cat3550 with latest EMI IOS
>
> Desmond, I haven't used a routing protocol with the 3550 yet but did you
> assign vlan 10 to the switch interface the router plugs into (switchport
> access vlan 10)? This should allow the router's interface to
> communicate
> with the vlan 10 interface on the 3550 by putting them into the same
> broadcast domain.
>
> Rik
>
> -----Original Message-----
> From: Desmond [mailto:cciestudy@sympatico.ca]
> Sent: Wednesday, December 04, 2002 3:13 PM
> To: ccielab@groupstudy.com
> Subject: Question about Cat3550 with latest EMI IOS
>
>
> I found the Interface vlan x will not pass routing to a router on same
> VLan.
> I need to change the port with "no switch port" and assign IP to it in
> order
> to make it work. I think it worked before with the previous verion.
> Vlan
> interface will not be activated until there is at least one connection
> for
> that vlan.
>
> e.g.
>
> Cat3550
> Inter vlan 10
> ip add 10.10.10.1
>
> Router Eigrp 1
> network 10.0.0.0
>
>
> 2600
>
> Inte fa 0/0
> ip add 10.10.10.2
>
> Router Eigrp 1
> network 10.0.0.0
>
>
> Appreicate for anyone provide information !
This archive was generated by hypermail 2.1.4 : Fri Jan 17 2003 - 17:21:39 GMT-3