From: Peng Zheng (zpnist@yahoo.com)
Date: Fri Nov 29 2002 - 17:41:55 GMT-3
Yes. 192.168.4.0 in the routing table for R13 and the
network 192.168.1.0 in the routing table for R3.
I found the tunnel on R3 is up, line protocol is up.
But the tunnel on R13 is up, but line protocol is
down. I can not figure out what cause this result.
--- mnmbaker@cfl.rr.com wrote:
> My apologies, you are correct (I need to learn to
> read better!). Is the network
> 192.168.4.0 in the routing table for R13 and the
> network 192.168.1.0 in the
> routing table for R3?
>
> Mark
>
> > Sorry. But I can not find which one I violate.
> > Because source and destination are interface IPs.
> THe
> > IPs on tunnel interfaces are unique.
> >
> > --- mnmbaker@cfl.rr.com wrote:
> > > Your tunnel source and destinations need to
> point to
> > > actual IPs on the routers.
> > > The "source" should be an interface IP on the
> local
> > > router, the "dest" should
> > > be an interface IP on the remote router.
> > > For R3, your source could be 10.3.1.3 and dest
> could
> > > be 10.2.1.13, then reverse
> > > for source and dest on R13.
> > > The IP address on the tunnel interface is part
> of
> > > the tunnel's network, which
> > > needs to be unique from the other interfaces.
> > >
> > > Mark
> > >
> > > > (lo0)R3(e0)----(e0)R5(s0.1)----(s0)R13(e0)
> > > >
> > > > IP for E3:
> > > > lo0: 10.3.1.3/24
> > > > e0: 192.168.4.3/24
> > > >
> > > > IP for R13:
> > > > s0: 192.168.1.13/28
> > > > e0: 10.2.1.13/24
> > > >
> > > > There is a tunnel is configured between R3 and
> > > R13.
> > > >
> > > > OSPF is runing between R3 and R5, R5 and R13
> > > > EIGRP is running on tunnel and lo0 of R3 and
> e0 of
> > > > R13.
> > > > But OSPF works well, but I cann not see tunnel
> in
> > > > routing table and R13 can not see lo0 of R3,
> R3
> > > can
> > > > not see e0 of R13.
> > > >
> > > > Below is their configuation:
> > > > ---------------------------------------------
> > > > !
> > > > version 12.1
> > > > service timestamps debug uptime
> > > > service timestamps log uptime
> > > > no service password-encryption
> > > > !
> > > > hostname r3
> > > > !
> > > > enable secret 5 $1$MZ4K$RZXlOUh3c8a5HB.ImaVRl0
> > > > !
> > > > !
> > > > !
> > > > !
> > > > !
> > > > ip subnet-zero
> > > > no ip domain-lookup
> > > > !
> > > > cns event-service server
> > > > !
> > > > !
> > > > !
> > > > !
> > > > interface Loopback0
> > > > ip address 129.3.3.3 255.255.255.0
> > > > !
> > > > interface Loopback1
> > > > ip address 10.3.1.3 255.255.255.0
> > > > !
> > > > interface Tunnel0
> > > > ip address 10.4.1.3 255.255.255.0
> > > > tunnel source 192.168.4.3
> > > > tunnel destination 192.168.1.13
> > > > !
> > > > interface Ethernet0
> > > > ip address 192.168.4.3 255.255.255.0
> > > > ip ospf message-digest-key 1 md5 cisco
> > > > !
> > > > interface Serial0
> > > > no ip address
> > > > shutdown
> > > > no fair-queue
> > > > !
> > > > interface Serial1
> > > > no ip address
> > > > shutdown
> > > > !
> > > > router eigrp 10
> > > > network 10.0.0.0
> > > > no auto-summary
> > > > no eigrp log-neighbor-changes
> > > > !
> > > > router ospf 1
> > > > log-adjacency-changes
> > > > area 3 authentication message-digest
> > > > network 129.3.3.3 0.0.0.0 area 3
> > > > network 192.168.4.3 0.0.0.0 area 3
> > > > !
> > > > ip classless
> > > > no ip http server
> > > > !
> > > > !
> > > > !
> > > > line con 0
> > > > exec-timeout 0 0
> > > > transport input none
> > > > line aux 0
> > > > line vty 0 4
> > > > login
> > > > !
> > > > end
> > > >
> > > > ________________________________________-
> > > > version 12.1
> > > > service timestamps debug uptime
> > > > service timestamps log uptime
> > > > no service password-encryption
> > > > !
> > > > hostname r13
> > > > !
> > > > enable secret 5 $1$5fx9$JtLJ8cAJWgL2V9o1/MvOQ1
> > > > !
> > > > !
> > > > !
> > > > !
> > > > !
> > > > ip subnet-zero
> > > > no ip domain-lookup
> > > > !
> > > > cns event-service server
> > > > !
> > > > interface Loopback0
> > > > ip address 129.13.13.13 255.255.255.0
> > > > !
> > > > interface Tunnel0
> > > > ip address 10.4.1.13 255.255.255.0
> > > > tunnel source 192.168.1.13
> > > > tunnel destination 193.168.4.3
> > > > !
> > > > interface Ethernet0
> > > > ip address 10.2.1.13 255.255.255.0
> > > > no keepalive
> > > > !
> > > > interface Serial0
> > > > ip address 192.168.1.13 255.255.255.240
> > > > encapsulation frame-relay
> > > > ip ospf message-digest-key 1 md5 cisco
> > > > ip ospf network broadcast
> > > > frame-relay map ip 192.168.1.5 301 broadcast
> > > > no frame-relay inverse-arp
> > > > !
> > > > interface Serial1
> > > > no ip address
> > > > shutdown
> > > > !
> > > > router eigrp 10
> > > > network 10.0.0.0
> > > > no auto-summary
> > > > no eigrp log-neighbor-changes
> > > > !
> > > > router ospf 1
> > > > log-adjacency-changes
> > > > area 0 authentication message-digest
> > > > network 129.13.13.13 0.0.0.0 area 0
> > > > network 192.168.1.13 0.0.0.0 area 0
> > > > !
> > > > ip classless
> > > > no ip http server
> > > > !
> > > > !
> > > > line con 0
> > > > exec-timeout 0 0
> > > > transport input none
> > > > line aux 0
> > > > line vty 0 4
> > > > login
> > > > !
> > > > end
> > > > _______________________________________
> > > >
> > > >
> > > > Does anyone know why?
> > > >
> > > >
>
=== message truncated ===
This archive was generated by hypermail 2.1.4 : Tue Dec 03 2002 - 07:23:12 GMT-3