From: ccna instructor (ccna20877@yahoo.com)
Date: Mon Nov 18 2002 - 23:28:21 GMT-3
Configure ppp multilink at both
Check your spids are correct ( check with examples on Cisco site or book)
Check Dialer list is also configured on both.
sadiq
John Tafasi <johntafasi@yahoo.com> wrote:John,
Below is the configuration for both ISDN routers. I guess the reason for
this error message is that the second B channel of the oposite router has a
different phone number than the one listed in the dialer map command?
R2-2516#show run
Building configuration...
hostname r2-2516
interface BRI0
ip address 10.10.10.1 255.255.255.0
no ip directed-broadcast
dialer map ip 10.10.10.2 broadcast 8358662
dialer load-threshold 70 either
dialer-group 1
isdn switch-type basic-ni
isdn spid1 0835866101
isdn spid2 0835866301
no cdp enable
----------------------------------------
R5-2503#show run
Building configuration...
!
interface BRI0
ip address 10.10.10.2 255.255.255.0
dialer map ip 10.10.10.1 broadcast 8358661
dialer load-threshold 70 either
dialer-group 1
isdn switch-type basic-ni
isdn spid1 0835866201
isdn spid2 0835866401
cdapi buffers regular 0
cdapi buffers raw 0
cdapi buffers large 0
no cdp enable
----- Original Message -----
From: "Gibbs, John"
To: "'John Tafasi'"
Sent: Monday, November 18, 2002 2:52 AM
Subject: RE: ISDN dialer load-threshold
> Hi John
>
> Have you entered "ppp multilink" and "dialer-load threshold %"? A copy
of your config would be helpful
>
> Regards
> John Gibbs CCNP CNE ACA
> Senior Network Consultant
> Engineering Services
> Service Delivery
> Internet Services
>
> Cable & Wireless
> Delivering the Internet promise
> www.cw.com
>
> email: john.gibbs@cw.com
>
>
> -----Original Message-----
> From: John Tafasi [mailto:johntafasi@yahoo.com]
> Sent: 18 November 2002 09:40
> To: ccielab
> Subject: ISDN dialer load-threshold
>
>
> My router below is trying to fire the second B channel to add more
bandwidth to an open connection but it fails every time it tries to do so. I
receive the following message. Can some one tell me why the call is being
rejected.
>
> Thanks
>
>
>
> 22:58:07: ISDN BR0: TX -> SETUP pd = 8 callref = 0x06
> 22:58:07: Bearer Capability i = 0x8890
> 22:58:07: Channel ID i = 0x83
> 22:58:07: Keypad Facility i = '8358661'
> 22:58:07: ISDN BR0: RX <- DISCONNECT pd = 8 callref = 0x86
> 22:58:07: Cause i = 0x8081 - Unallocated/unassigned number
> 22:58:07: ISDN BR0: TX -> RELEASE pd = 8 callref = 0x06
> 22:58:07: ISDN BR0: RX <- RELEASE_COMP pd = 8 callref = 0x86
> 22:58:07: ISDN BR0: Setup was rejected, cause = 60
> R5-2503#
>
>
> **********************************************************************
> This message may contain information which is confidential or privileged.
> If you are not the intended recipient, please advise the sender
immediately
> by reply e-mail and delete this message and any attachments
> without retaining a copy.
>
> **********************************************************************
---------------------------------
Do you Yahoo!?
Yahoo! Web Hosting - Let the expert host your site
This archive was generated by hypermail 2.1.4 : Tue Dec 03 2002 - 07:23:05 GMT-3