From: John Tafasi (johntafasi@yahoo.com)
Date: Mon Nov 18 2002 - 21:04:55 GMT-3
yes this worked fine
Thank you all
----- Original Message -----
From: "Gibbs, John" <John.Gibbs@cwcom.cwplc.com>
To: "'John Tafasi'" <johntafasi@yahoo.com>
Sent: Monday, November 18, 2002 4:06 AM
Subject: RE: ISDN dialer load-threshold
> John
>
> A couple of things:-
>
> 1. You need to apply 2 dialer maps on r2-2516: you have the first dialer
map there which maps to 8358662, but you need to insert a second one to the
same IP address but to 8358664. The reason is that at the moment you have
only asked to call one spid on the remote router.
>
> 2. I think on R5-2503 you may also need to add the actual strings after
the spid statements - ie on R5-2503 the spids should be:-
> isdn spid1 0835866201 8358662
> isdn spid2 0835866401 8358664
>
> Of course if you want r5 to be able to dial r2, you will have to do the
same on r2-2516
>
> Try this and see if it works
>
> Rgds
> JG
>
> -----Original Message-----
> From: John Tafasi [mailto:johntafasi@yahoo.com]
> Sent: 18 November 2002 10:37
> To: ccielab; Gibbs, John
> Subject: Re: ISDN dialer load-threshold
>
>
> John,
>
> Below is the configuration for both ISDN routers. I guess the reason for
this error message is that the second B channel of the oposite router has a
different phone number than the one listed in the dialer map command?
>
> R2-2516#show run
> Building configuration...
>
> hostname r2-2516
> interface BRI0
> ip address 10.10.10.1 255.255.255.0
> no ip directed-broadcast
> dialer map ip 10.10.10.2 broadcast 8358662
> dialer load-threshold 70 either
> dialer-group 1
> isdn switch-type basic-ni
> isdn spid1 0835866101
> isdn spid2 0835866301
> no cdp enable
> ----------------------------------------
> R5-2503#show run
> Building configuration...
> !
> interface BRI0
> ip address 10.10.10.2 255.255.255.0
> dialer map ip 10.10.10.1 broadcast 8358661
> dialer load-threshold 70 either
> dialer-group 1
> isdn switch-type basic-ni
> isdn spid1 0835866201
> isdn spid2 0835866401
> cdapi buffers regular 0
> cdapi buffers raw 0
> cdapi buffers large 0
> no cdp enable
>
>
> ----- Original Message -----
> From: "Gibbs, John" <John.Gibbs@cwcom.cwplc.com>
> To: "'John Tafasi'" <johntafasi@yahoo.com>
> Sent: Monday, November 18, 2002 2:52 AM
> Subject: RE: ISDN dialer load-threshold
>
>
> > Hi John
> >
> > Have you entered "ppp multilink" and "dialer-load threshold %"? A copy
> of your config would be helpful
> >
> > Regards
> > John Gibbs CCNP CNE ACA
> > Senior Network Consultant
> > Engineering Services
> > Service Delivery
> > Internet Services
> >
> > Cable & Wireless
> > Delivering the Internet promise
> > www.cw.com <http://www.cw.com>
> >
> > email: john.gibbs@cw.com
> >
> >
> > -----Original Message-----
> > From: John Tafasi [mailto:johntafasi@yahoo.com]
> > Sent: 18 November 2002 09:40
> > To: ccielab
> > Subject: ISDN dialer load-threshold
> >
> >
> > My router below is trying to fire the second B channel to add more
> bandwidth to an open connection but it fails every time it tries to do so.
I receive the following message. Can some one tell me why the call is being
rejected.
> >
> > Thanks
> >
> >
> >
> > 22:58:07: ISDN BR0: TX -> SETUP pd = 8 callref = 0x06
> > 22:58:07: Bearer Capability i = 0x8890
> > 22:58:07: Channel ID i = 0x83
> > 22:58:07: Keypad Facility i = '8358661'
> > 22:58:07: ISDN BR0: RX <- DISCONNECT pd = 8 callref = 0x86
> > 22:58:07: Cause i = 0x8081 - Unallocated/unassigned number
> > 22:58:07: ISDN BR0: TX -> RELEASE pd = 8 callref = 0x06
> > 22:58:07: ISDN BR0: RX <- RELEASE_COMP pd = 8 callref = 0x86
> > 22:58:07: ISDN BR0: Setup was rejected, cause = 60
> > R5-2503#
> >
> >
> > **********************************************************************
> > This message may contain information which is confidential or
> > privileged. If you are not the intended recipient, please advise the
> > sender
> immediately
> > by reply e-mail and delete this message and any attachments without
> > retaining a copy.
> >
> > **********************************************************************
>
>
> **********************************************************************
> This message may contain information which is confidential or privileged.
> If you are not the intended recipient, please advise the sender
immediately
> by reply e-mail and delete this message and any attachments
> without retaining a copy.
>
> **********************************************************************
This archive was generated by hypermail 2.1.4 : Tue Dec 03 2002 - 07:23:05 GMT-3