From: Ayman Hamza (ayhamza@cisco.com)
Date: Sun Nov 03 2002 - 12:09:22 GMT-3
Hi Peter;
Thanks for the reply. But the question didn't say to apply this
CQ configuration on the ethernet! It's saying to give all the DLSw+ related
traffic coming from ethernet interface 50% of the avialable bandwidth
on the outbound interfaces that will establish outbound DLSw+ peering
sessions. So I don't think it's correct to apply this CQ on ethernet interface.
More over, Can you PLS let me know How you made a decision that the below
byte-counts will give 50% for the DLSw+ traffic??!! How you make your
calculations?!! what are the frame sizes you used!!!!
Thanks for your reply in advance
Ayman
> From pita40@hotmail.com Sun Nov 3 15:54:41 2002
> X-Originating-IP: [68.54.241.33]
> From: "peter brown" <pita40@hotmail.com>
> To: ayhamza@cisco.com, Sam.MicroGate@usa.telekom.de, ccielab@groupstudy.com
> Subject: Re: Heeelp!! Urgent !! CCIE question about CQ
> Date: Sun, 03 Nov 2002 14:54:31 +0000
> Mime-Version: 1.0
> X-OriginalArrivalTime: 03 Nov 2002 14:54:31.0416 (UTC) FILETIME=[EA742780:01C28348]
>
>
> queue-list 1 protocol ip 1 tcp 2065
> queue-list 1 default 2
> queue-list 1 queue 1 byte-count 5000
> queue-list 1 queue 2 byte-count 5000
>
> then apply this queue-list to e0
>
> 2065 is dlsw port
>
> If you were asked to distinguish between dlsw traffics then you will have to
> use sap priority or local address priority.
>
> This config above gives 50% to dlsw and 50% to all other traffic.
>
> Peter
>
>
>
>
>
> >From: Ayman Hamza <ayhamza@cisco.com>
> >Reply-To: Ayman Hamza <ayhamza@cisco.com>
> >To: Sam.MicroGate@usa.telekom.de, ccielab@groupstudy.com
> >Subject: Heeelp!! Urgent !! CCIE question about CQ Date: Sun, 3 Nov 2002
> >14:23:09 +0100 (CET)
> >
> >Team;
> >
> >Sorry for that high urgency. I have a question from a CCIE LAB exam which
> >saying - exact wording - :
> >
> >-----------------------------------------------------------------
> >
> >On a router that you have DLSw+ config , configure CQ such that the
> >DLSw+ traffic coming from ethernet interfaces to be allocated 50% of the
> >outbound interface over which the DLSw+ session will be established.
> >
> >-----------------------------------------------------------------
> >
> >
> >I don't really how to resolve this! If I configured queue-list for the
> >traffic coming from ethernet interface that SNA/Netbios staions are
> >setting,
> >How I can specify in the queue-list command a definition that
> >associates the DLSw+traffic and incoming interface traffic at teh sametime
> >???!
> >
> >I mean:
> >
> >queue-list 1 interface ethernet0 1
> >
> >There is nothing in the above command that let me associates the traffic
> >coming from ethernet0 with DLSW+, the above command gives a defintion for
> >all the traffic coming from ethrnet 0 whether it's DLSw+ related or not!
> >How
> >I can solve this. More over, How I can specify the correct Byte counts!!!!!
> >
> >
> >Appreciating any reply!
> >
> >
> >Regards;
> >Ayman
>
>
> _________________________________________________________________
> Unlimited Internet access for only $21.95/month. Try MSN!
> http://resourcecenter.msn.com/access/plans/2monthsfree.asp
This archive was generated by hypermail 2.1.4 : Tue Dec 03 2002 - 07:22:51 GMT-3