From: aansar@sscomp.com.sg
Date: Thu Oct 24 2002 - 00:46:58 GMT-3
yes , as i checked adjancy is formed , LSA also propagated , but it is not
installed in the routing table ,
if you issue show ip ospf data router command in the hub router , you can
see the LSA's from that spoke but it is listed as
.
Adv Router is not-reachable
> LS age: 1625
> Options: (No TOS-capability, DC)
> LS Type: Router Links
> Link State ID: 7.7.7.7
> Advertising Router: 7.7.7.7
> LS Seq Number: 80000005
> Checksum: 0xF048
> Length: 156
> Number of Links: 11
the same scenario i tried like this
in the hub i used ip ospf multi point interface and in the spoke i used ip
opsf point to point network , then there is hello mis match , i adjusted
spoke hello interval to match hub , then everything is fine ,adjancy is
created , LSA advertised , and it is intsalled in the routing table too..
thanks guys
aa
Chris <clarson52@comcast.net>
Sent by: nobody@groupstudy.com
10/24/2002 11:27 AM
Please respond to Chris
To: aansar@sscomp.com.sg, Donny MATEO <donny.mateo@sg.ca-indosuez.com>
cc: ccielab@groupstudy.com, nobody@groupstudy.com
Subject: Re: Adv Router is not-reachable
Not possible.
The problem is not just the timers. A sub interface will be a
point-to-point
network type and there is No DR needed. If you can't do a subinterface on
the other side then it will be non-broadcast and will need a DR.
A Physical interface is Non-broadcast and needs a DR. And in frame the DR
should be on the hub. So changing the timers is not going to do anything.
I
am quite sure this is not possible. If it is I would love to see how it is
done.
----- Original Message -----
From: <aansar@sscomp.com.sg>
To: "Donny MATEO" <donny.mateo@sg.ca-indosuez.com>
Cc: <ccielab@groupstudy.com>; <nobody@groupstudy.com>
Sent: Wednesday, October 23, 2002 10:37 PM
Subject: Re: Adv Router is not-reachable
> condition is like this
> do not use ip ospf network command when configuring the OSPF
> use only subinterface in the hub router not in the spoke routers
>
>
****************************************************************************
> Message from:
>
> A.S Ahmed Ansar
> Customer Support Group
> Seven Seas Computers.com (Singapore) Pte LTD
> email: aansar@sscomp.com.sg
> Tel:+65 551 5726 or Mobile: +65 9012 2488
> Fax:+65 5515 755
> visit us at http://www.sscomp.com.sg
>
>
***************************************************************************
>
>
>
>
> "Donny MATEO" <donny.mateo@sg.ca-indosuez.com>
> Sent by: nobody@groupstudy.com
> 10/24/2002 10:19 AM
> Please respond to "Donny MATEO"
>
>
> To: aansar@sscomp.com.sg
> cc: ccielab@groupstudy.com, nobody@groupstudy.com
> Subject: Re: Adv Router is not-reachable
>
>
> on which router are you prohibited to use ip ospf network x.x.x.x. ? And
> what is the wording. If it
> specified only one router you can use it on the other router. Or if it's
> just say don't use ip ospf
> network broadcast, you can always use ip ospf network
point-to-multipoint.
>
>
> Donny
>
>
>
> aansar@sscomp.com
> .sg To:
ccielab@groupstudy.com
>
> Sent by: cc:
> nobody@groupstudy Subject: Adv Router is
> not-reachable
> .com
>
>
> 24-10-2002 09:01
> Please respond to
> aansar
>
>
>
>
>
>
> sh ip os data router , shows
> Adv Router is not-reachable
> but adjutancy has been established already .. what could be the problem.
>
> R1
> has point to point frame relay interface towards R2
>
> R2
> normal plain serial interface (initially hello mis matches , i changed
> hello interval of R2 )
>
> Adancy has been estabilised , no problem
> but R2 routes are not visible in R1, (sh ip os data router , shows all
the
> LSA of R2 but the first line tells adv router is not reachable)
>
> Adv Router is not-reachable
> LS age: 1625
> Options: (No TOS-capability, DC)
> LS Type: Router Links
> Link State ID: 7.7.7.7
> Advertising Router: 7.7.7.7
> LS Seq Number: 80000005
> Checksum: 0xF048
> Length: 156
> Number of Links: 11
>
> thanks
> aa
This archive was generated by hypermail 2.1.4 : Tue Nov 05 2002 - 08:35:55 GMT-3