From: Erick B. (erickbe@yahoo.com)
Date: Sat Oct 05 2002 - 19:14:20 GMT-3
Adarsh,
It depends on how granular you want to get. You could
mark inbound packets from your voice-enabled devices
with ip precedence of 5, etc then on the class just
match ip precedence 5.
In the sample I posted, theres a chance non-voice
traffic that falls in the same port ranges as voice
will be prioritized as voice traffic.
--- Adarsh Singh <adarshs@hclinfinet.net> wrote:
> Hi
>
> Do i need to mark packets on the ethernet port first
> , by using the
> acces-list as you have mentioned
>
> access-list 100 permit ip any any precedence
> critical
> > access-list 100 permit udp any any range 16384
> 32767
> > access-list 100 permit ip any any dscp ef
> > access-list 100 permit udp any range 16384 32767
> any
>
> But in my scenario i would be marking the packets
> only between the first
> voip box & the second one , i.e 10.66.6.126 &
> 10.66.6.35.
> How do i apply the marking of the packets on the
> ethernet, could you tell
> me how do that part , do i need to apply this
> marking on both ends of the
> router at the ethernet port.
>
> This is test setup so i have no other traffic
> between the two routers .
> Inspite of the fact thet packets are matching the
> qos is not working, the
> voice is still breaking a lot .
> the current config for the serial port for both
> routers are as follows :
>
>
> router 1
>
> class-map voice
> match access-group 102
> !
> !
> policy-map test
> class voice
> priority 30
> class class-default
> fair-queue
> policy-map tes
>
>
> interface Serial0
> description connected to Infinet 64K leased line
> for vpn
> bandwidth 64
> ip address 10.66.2.122 255.255.255.252
> no ip route-cache
> no ip mroute-cache
> load-interval 30
> max-reserved-bandwidth 90
> service-policy output test
> clockrate 64000
>
> access-list 102 permit udp host 10.66.6.124 gt 20000
> host 10.66.6.36 gt
> 20000
>
>
> router 2
>
>
> class-map voice
> match access-group 102
> !
> !
> policy-map test
> class voice
> priority 30
> class class-default
> fair-queue
> !
> interface Serial0
> description connected to Internet
> bandwidth 64
> ip address 10.66.2.98 255.255.255.252
> no ip route-cache
> no ip mroute-cache
> load-interval 30
> max-reserved-bandwidth 90
> service-policy output test
> !
> access-list 102 permit udp host 10.66.6.36 gt 20000
> host 10.66.6.124 gt
> 20000
>
> Kindly let me know if you have any ideas.
>
> Rgds
> Adarsh
>
>
>
>
>
>
>
>
>
> Adarsh
> ----- Original Message -----
> From: "Erick B." <erickbe@yahoo.com>
> To: "Adarsh Singh" <adarshs@hclinfinet.net>; "CCIE
> Group Study (E-mail)"
> <ccielab@groupstudy.com>
> Sent: Friday, October 04, 2002 9:35 PM
> Subject: Re: CBWFQ not working on 1603 for
> VOICE--HELP NEEDED URGENTLY
>
>
> > Try making your classes and ACLs more detailed.
> >
> > class-map match-all voip_traffic
> > match access-group 100
> > class-map match-all voip_control
> > match access-group 101
> >
> > policy-map llq_256_voice_3calls
> > class voip_traffic
> > priority 134
> > class voip_control
> > bandwidth 8
> > class class-default
> > fair-queue
> >
> > access-list 100 permit ip any any precedence
> critical
> > access-list 100 permit udp any any range 16384
> 32767
> > access-list 100 permit ip any any dscp ef
> > access-list 100 permit udp any range 16384 32767
> any
> > access-list 101 permit tcp any range 2000 2002 any
> > access-list 101 permit tcp any any range 2000 2002
> > access-list 101 permit tcp any range 11000 11999
> any
> > access-list 101 permit tcp any any range 11000
> 11999
> > access-list 101 permit tcp any any eq 1720
> > access-list 101 permit tcp any eq 1720 any
> >
> >
> > --- Adarsh Singh <adarshs@hclinfinet.net> wrote:
> > > Hi Erik
> > >
> > > I am getting the matched packets on the
> access-list
> > > for the ip packets, but
> > > still when i start the voice conversation
> between
> > > the two boxes, it is not
> > > reserving the 40 Kbps , when the ftp is going on
> ,
> > > the traffic reaches to
> > > 62 Kbps , and the voice breaks while talking
> ,pls do
> > > suggest what to do.
> > >
> > > Rgds
> > > Adarsh Singh
> > > ----- Original Message -----
> > > From: "Erick B." <erickbe@yahoo.com>
> > > To: "Adarsh Singh" <adarshs@hclinfinet.net>;
> "CCIE
> > > Group Study (E-mail)"
> > > <ccielab@groupstudy.com>
> > > Sent: Friday, October 04, 2002 10:54 AM
> > > Subject: Re: CBWFQ not working on 1603 for
> > > VOICE--HELP NEEDED URGENTLY
> > >
> > >
> > > > Thats because UDP is being matched by the
> first
> > > entry
> > > > in the ACL. ACL stops processing after a
> match. IP
> > > > covers ICMP, UDP, and TCP.
> > > >
> > > > --- Adarsh Singh <adarshs@hclinfinet.net>
> wrote:
> > > > > Hi ,=20
> > > > >
> > > > > I have been trying to implement CBWFQ
> between
> > > two
> > > > > cisco 1603 routers.
> > > > >
> > > > >
> > > > > PC
> > > > > |
> > > > >
> > > >
> > >
> >
>
OAHO(router1)(serial0)------backtoback-------(serial0)OAREMOTE(router2)--=
> > > > > --VOIPBOX1(10.66.6.126)
> > > > > |
> > > (64
> > > > > Kbps) =
> > > > >
> > > |
> > > > > |
> > > > > =
> > > > >
> > > > > PC
> > > > >
> > > > > VOIPBOX2
> > > > > (10.66.6.35)
> > > > >
> > > > > Now the default queing for the two routers
> is
> > > > > Weighted fair quwing .
> > > > >
> > > > > Now i have reserved 30 Kbps bandwidth
> between
> > > the
> > > > > two router for the =
> > > > > voice traffic , the voipbox is uing UDP
> ports
> > > > > greater than 20000.
> > > > >
> > > > > So after configuring the routers , i do a
> > > multiple
> > > > > ftp sessions between =
> > > > > the two PC, so that the traffic between the
> two
> > > > > serial interfaces =
> > > > > touches 62 Kbps .
> > > > >
> > > > > Now when i start talking between the two
> VOIP
> > > boxes
> > > > > , i dont see the =
> > > > > CBWFQ kicking in & reserving the necessary
> > > bandwidth
> > > > > as i have =
> > > > > provisioned .
> > > > >
> > > > > I am enclosing both the router configuration
> :
> > > > >
> > > > > CONFIG OF OAHO=20
> > > > >
> > > > > OAHO=20
> > > > >
> > > > > sh ru=20
> > > > > Building configuration...
> > > > >
> > > > > Current configuration : 1146 bytes
> > > > > !
> > > > > version 12.1
> > > > > no service single-slot-reload-enable
> > > > > service timestamps debug uptime
> > > > > service timestamps log uptime
> > > > > no service password-encryption
> > > > > !
> > > > > hostname OAHO
> > > > > !
> > > > > !
> > > > > !
> > > > > class-map voice
> > > > > match access-group 101
> > > > > !
> > > > > !
> > > > > policy-map test
> > > > > class voice
> > > > > priority 40
> > > > > !
> > > > > ip subnet-zero
> > > > > ip tftp source-interface Ethernet0
> > > > > !
> > > > > !
> > > > > interface Ethernet0
> > > > > description connected to EthernetLAN_1
> > > > > ip address 10.66.6.33 255.255.255.248
> > > > > no cdp enable
> > > > > !
> > > > > interface Serial0
> > > > > description connected to Internet
> > > > > bandwidth 64
> > > > > ip address 10.66.2.98 255.255.255.252
> > > > > no ip route-cache
> > > > > no ip mroute-cache
> > > > > service-policy output test=20
> > > > > load-interval 30
> > > > > max-reserved-bandwidth 90
> > > > > !
> > > > > interface BRI0
> > > > > no ip address
> > > > > shutdown
> > > > > ip classless
> > > > > ip route 0.0.0.0 0.0.0.0 10.66.2.97
> > > > > no ip http server
> > > > > !
> > > > > access-list 101 permit ip host 10.66.6.35
> host
> > > > > 10.66.6.126
> > > > > access-list 101 permit udp host 10.66.6.35
> gt
> > > 20000
> > > > > host 10.66.6.126 gt =
> > > > > 20000
> > > > > dialer-list 1 protocol ip permit
> > > > > tftp-server flash:c1600-sy-mz.121-15.bin
> > > > > !
> > > > > line con 0
> > > > > exec-timeout 0 0
> > > > > password vpn
> > > > > login
> > > > > line vty 0 4
> > > > > exec-timeout 60 0
> > > > > password vpn
> > > > > login
> > > > > transport preferred none
> > > > > !
> > > > > end
> > > > >
> > > > > OAHO# show po
> > > > > OAHO# show policy-map=20
> > > > > Policy Map test
> > > > > Weighted Fair Queueing
> > > > > Class voice=20
> > > > > Strict Priority
> > > > > Bandwidth 40 (kbps)
> > > > >
> > > > > OAHO#show policy-map=20
> > > > > Policy Map test
> > > > > Weighted Fair Queueing
> > > > > Class voice=20
> > > > > Strict Priority
> > > > > Bandwidth 40 (kbps)
> > > > >
> > > > > OAHO#show policy-map int se 0
> > > > > OAHO#show int se 0
> > > > > Serial0 is up, line protocol is up=20
> > > > > Hardware is QUICC Serial
> > > > > Description: connected to Internet
> > > > > Internet address is 10.66.2.98/30
> > > > > MTU 1500 bytes, BW 64 Kbit, DLY 20000
> usec,=20
> > > > > reliability 255/255, txload 3/255,
> rxload
> > > 3/255
> > > > > Encapsulation HDLC, loopback not set
> > > > > Keepalive set (10 sec)
> > > > > Last input 00:00:00, output 00:00:00,
> output
> > > hang
> > > > > never
> > > > > Last clearing of "show interface" counters
> > > > > 00:08:54
> > > > > Input queue: 0/75/0/0
> > > (size/max/drops/flushes);
> > > > > Total output drops: 0
> > > > > Queueing strategy: fifo
> > > > > Output queue :0/40 (size/max)
> > > > > 30 second input rate 1000 bits/sec, 4
> > > packets/sec
> > > > > 30 second output rate 62000 bits/sec, 3
> > > > > packets/sec
> > > > > 816 packets input, 39184 bytes, 0 no
> buffer
> > > > > Received 69 broadcasts, 0 runts, 0
> giants,
> > > 0
> > > > > throttles
> > > > > 0 input errors, 0 CRC, 0 frame, 0
> overrun,
> > > 0
> > > > > ignored, 0 abort
> > > > > 717 packets output, 46507 bytes, 0
> > > underruns
> > > > > 0 output errors, 0 collisions, 1
> interface
> > > > > resets
> > > > > 0 output buffer failures, 0 output
> buffers
> > > > > swapped out
> > > > > 6 carrier transitions
> > > > > DCD=3Dup DSR=3Dup DTR=3Dup RTS=3Dup
> > > > > CTS=3Dup
> > > > > --
> > > > >
> > > > > OAHO#show queue se 0
> > > > > Show queue not supported with FIFO queueing
> > > > >
> > > > > OAREMOTE CONFIG
> > > > >
> > > > >
> > > > > sh ru=20
> > > > > Building configuration...
> > > > >
> > > > > Current configuration : 1316 bytes
> > > > > !
> > > > > version 12.1
> > > > > no service single-slot-reload-enable
> > > > > service timestamps debug uptime
> > > > > service timestamps log uptime
> > > > > no service password-encryption
> > > > > !
> > > > > hostname OAREMOTE
> > > > > !
> > > > > enable secret 5
> $1$r1WR$YWvapuJdPcjur/4S6MRKv.
> > > > > !
> > > > > username dlinpc password 0 npc
> > > > > username noidad32 password 0 d32
> > > > > !
> > > > > class-map voice
> > > > > match access-group 101
> > > > > !
> > > > > !
> > > > > policy-map test
> > > > > class voice
> > > > > priority 40
> > > > > ip subnet-zero
> > > > > !
> > > > > isdn switch-type basic-net3
> > > > > !
> > > > > !
> > > > > !
> > > > > interface Ethernet0
> > > > > ip address 10.66.6.121 255.255.255.248
> > > > > ip nat inside
> > > > > no cdp enable
> > > > > !
> > > > > interface Serial0
> > > > > description connected to Infinet 64K leased
> > > line
> > > > > for vpn
> > > > > bandwidth 64
> > > > > ip address 10.66.2.122 255.255.255.252
> > > > > no ip route-cache
> > > > > no ip mroute-cache
> > > > > load-interval 30
> > > > > max-reserved-bandwidth 90
> > > > > service-policy output test
> > > > > clockrate 64000
> > > > > !
> > > > > interface BRI0
> > > > > description connected to NPC/D32
> > > > > no ip address
> > > > > encapsulation ppp
> > > > > isdn switch-type basic-net3
> > > > > no fair-queue
> > > > > no cdp enable
> > > > > !
> > > > > ip classless
> > > > > ip route 0.0.0.0 0.0.0.0 10.66.2.121
> > > > > no ip http server
> > > > > !
> > > > > access-list 101 permit ip host 10.66.6.126
> host
> > > > > 10.66.6.35
> > > > > access-list 101 permit udp host 10.66.6.126
> gt
> > > 20000
> > > > > host 10.66.6.36 gt =
> > > > > 20000
> > > > > dialer-list 1 protocol ip permit
> > > > > !
> > > > > line con 0
> > > > > exec-timeout 0 0
> > > > > password 111
> > > > > login
> > > > > line vty 0 password 111
> > > > > login
> > > > > !
> > > > > end
> > > > >
> > > > > OAREMOTE# show po
> > > > > OAREMOTE# show policy-map=20
> > > > > Policy Map test
> > > > > Weighted Fair Queueing
> > > > > Class voice=20
> > > > > Strict Priority
> > > > > Bandwidth 40 (kbps)
> > > > > OAREMOTE#show po
> > > > > OAREMOTE#show policy-map int se 0
> > > > > Serial0 output : test
> > > > > Weighted Fair Queueing
> > > > > Class voice=20
> > > > > Strict Priority
> > > > > Output Queue: Conversation 24=20
> > > > > Bandwidth 40 (kbps) Packets Matched
> 40
> > > > > (total drops/bytes drops) 5/380
> > > > > OAREMOTE#sjh=08 =08=08 =08=FF
> > > > >
> > > > > User Access Verification
> > > > >
> > > > > Password: =07=FF
> > > > > OAHO>telnet 10.66.6.12=08 =08=08 =08121
> > > > > Trying 10.66.6.121 ... Open
> > > > >
> > > > >
> > > > > =20
> > > > >
> > > > > OAREMOTE#show policy-map=20
> > > > > Policy Map test
> > > > > Weighted Fair Queueing
> > > > > Class voice=20
> > > > > Strict Priority
> > > > > Bandwidth 40 (kbps)
> > > > > OAREMOTE#show po
> > > > > OAREMOTE#show policy-map int se 0
> > > > > Serial0 output : test
> > > > > Weighted Fair Queueing
> > > > > Class voice=20
> > > > > Strict Priority
> > > > > Output Queue: Conversation 24=20
> > > > > Bandwidth 40 (kbps) Packets Matched
> 40
> > > > > (total drops/bytes drops) 5/380
> > > > > =20
> > > > > =20
> > > > > =20
> > > > > =20
> > > > > Now when i even see the access-list 101 , i
> dont
> > > see
> > > > > any match for the =
> > > > > UDP packets while talking , i fail to
> undertand
> > > that
> > > > > because when i do =
> > > > > debug ip packet detail , i see the udp ports
> > > been
> > > > > used while talking =
> > > > > between the voip box .
> > > > > =20
> > > > > Can some one help me out with this....needed
> > > help
> > > > > urgently .
> > > >
> > > >
> > > >
> > > >
> __________________________________________________
> > > > Do you Yahoo!?
> > > > New DSL Internet Access from SBC & Yahoo!
> > > > http://sbc.yahoo.com
> >
> >
> > __________________________________________________
> > Do you Yahoo!?
> > New DSL Internet Access from SBC & Yahoo!
> > http://sbc.yahoo.com
This archive was generated by hypermail 2.1.4 : Tue Nov 05 2002 - 08:35:40 GMT-3