From: Edwin Lacaden (rslab2002@yahoo.com)
Date: Wed Sep 11 2002 - 19:44:37 GMT-3
Larry,
If it was working before then it may be a cabling
problem. Try reverse telneting to line 65 to verify
that you can talk with the modem and issue an AT
commmand.
Another thing is to turn debug dialer ON and see what
happens during the dial up process. It should give you
a clue to where the problem is.
If that works then check on the router that you are
trying to dial, make sure the command "autoselect ppp"
is configured on line aux 0.
Hope this helps.
Edwin
--- "Roberts, Larry" <Larry.Roberts@expanets.com>
wrote:
> OK,
> I had this working at one point , but now I can't
> get it to work for the
> life of me...
>
> \I am trying to make the dialer0 interface bring up
> the As65 interface and
> make a connection across the link.
> If I set the as65 interface for async mode
> dedicated, the link comes up and
> stays up. Setting it to async mode interactive "HAD"
> worked for allowing
> A ping of the remote dialer IP to bring the link up.
> Now, all I get in the error log is no free dialer.
> I can do a show line and see everything appears fine
> , but a sho int as65
> show the interface down/down, while I expect
> UP/down.
>
> Anybody have any thoughts as to why the as65
> interface is down/down and im
> getting the no free-dialer starting fast idle timer
> message ?
>
> I think Its something Soooooo obvious but its
> escaping me?
> I can provide the other router config if needed.
>
> ############################################
> Router 1
> interface Async65
> no ip address
> encapsulation ppp
> no ip route-cache
> no ip mroute-cache
> dialer in-band
> dialer pool-member 1
> async default routing
> async dynamic routing
> async mode interactive
> !
> interface Dialer0
> ip address 192.168.12.1 255.255.255.0
> encapsulation ppp
> dialer pool 1
> dialer string 1234
> dialer-group 1
> no cdp enable
> !
> line aux 0
> script dialer myscript
> modem InOut
> transport input all
> speed 19200
> #######################################
> A show Line 65 on router 1 provides....
>
> * 65 AUX 19200/19200 - inout - - -
> 266 0 3031/1337443
> -
>
>
> Line 65, Location: "", Type: ""
> Length: 24 lines, Width: 80 columns
> Baud rate (TX/RX) is 19200/19200, no parity, 2
> stopbits, 8 databits
> Status: Ready, Active, No Exit Banner, CTS Raised,
> Modem Signals Polled
> Capabilities: Modem Callout, Modem RI is CD,
> Line usable as async interface
> Modem state: Ready
> Group codes: 0
> Modem hardware state: CTS* DSR* DTR RTS
> Special Chars: Escape Hold Stop Start Disconnect
> Activation
> ^^x none - - none
> Timeouts: Idle EXEC Idle Session Modem
> Answer Session Dispatch
> 00:10:00 never
> none not set
> Idle Session Disconnect
> Warning
> never
> Login-sequence User
> Response
> 00:00:30
> Autoselect Initial Wait
> not set
> Modem type is unknown.
> Session limit is not set.
> Time since activation: 00:05:18
> Editing is enabled.
> History is enabled, history size is 10.
> DNS resolution in show commands is enabled
> Full user help is disabled
> Allowed input transports are lat pad v120 mop telnet
> rlogin udptn nasi ssh.
> Allowed output transports are lat pad v120 mop
> telnet rlogin nasi ssh.
> Preferred transport is lat.
> No output characters are padded
> No special data dispatching characters
>
>
>
>
> Thanks
>
> Larry Roberts CCNP
> Expanets
> 5520 West 76th St.
> Indianapolis IN 46278
> 317.870.2550 Office
> 317.402.9730 Cell
> 813.655.2491 Fax
>
This archive was generated by hypermail 2.1.4 : Mon Oct 07 2002 - 07:43:49 GMT-3