From: Lim Meng Toon (limmti@yahoo.com.sg)
Date: Wed Sep 11 2002 - 22:05:08 GMT-3
Hi,
Try the following:
If need to, reboot your router on both end.
> ############################################
> Router 1
> interface Async65
> no ip address
> encapsulation ppp
> no ip route-cache
> no ip mroute-cache
> dialer in-band
> dialer pool-member 1
> async default routing
> async dynamic routing
> !
> interface Dialer0
> ip address 192.168.12.1 255.255.255.0
> encapsulation ppp
> dialer pool 1
> dialer string 1234
> dialer-group 1
> no cdp enable
> !
> line aux 0
exec-timout 0 0
> script dialer myscript
> modem Host <------(For the calling side)
> transport input all
> speed 19200
> flowcontrol hardware
--- "Roberts, Larry" <Larry.Roberts@expanets.com>
wrote: > OK,
> I had this working at one point , but now I can't
> get it to work for the
> life of me...
>
> \I am trying to make the dialer0 interface bring up
> the As65 interface and
> make a connection across the link.
> If I set the as65 interface for async mode
> dedicated, the link comes up and
> stays up. Setting it to async mode interactive "HAD"
> worked for allowing
> A ping of the remote dialer IP to bring the link up.
> Now, all I get in the error log is no free dialer.
> I can do a show line and see everything appears fine
> , but a sho int as65
> show the interface down/down, while I expect
> UP/down.
>
> Anybody have any thoughts as to why the as65
> interface is down/down and im
> getting the no free-dialer starting fast idle timer
> message ?
>
> I think Its something Soooooo obvious but its
> escaping me?
> I can provide the other router config if needed.
>
> ############################################
> Router 1
> interface Async65
> no ip address
> encapsulation ppp
> no ip route-cache
> no ip mroute-cache
> dialer in-band
> dialer pool-member 1
> async default routing
> async dynamic routing
> async mode interactive
> !
> interface Dialer0
> ip address 192.168.12.1 255.255.255.0
> encapsulation ppp
> dialer pool 1
> dialer string 1234
> dialer-group 1
> no cdp enable
> !
> line aux 0
> script dialer myscript
> modem InOut
> transport input all
> speed 19200
> #######################################
> A show Line 65 on router 1 provides....
>
> * 65 AUX 19200/19200 - inout - - -
> 266 0 3031/1337443
> -
>
>
> Line 65, Location: "", Type: ""
> Length: 24 lines, Width: 80 columns
> Baud rate (TX/RX) is 19200/19200, no parity, 2
> stopbits, 8 databits
> Status: Ready, Active, No Exit Banner, CTS Raised,
> Modem Signals Polled
> Capabilities: Modem Callout, Modem RI is CD,
> Line usable as async interface
> Modem state: Ready
> Group codes: 0
> Modem hardware state: CTS* DSR* DTR RTS
> Special Chars: Escape Hold Stop Start Disconnect
> Activation
> ^^x none - - none
> Timeouts: Idle EXEC Idle Session Modem
> Answer Session Dispatch
> 00:10:00 never
> none not set
> Idle Session Disconnect
> Warning
> never
> Login-sequence User
> Response
> 00:00:30
> Autoselect Initial Wait
> not set
> Modem type is unknown.
> Session limit is not set.
> Time since activation: 00:05:18
> Editing is enabled.
> History is enabled, history size is 10.
> DNS resolution in show commands is enabled
> Full user help is disabled
> Allowed input transports are lat pad v120 mop telnet
> rlogin udptn nasi ssh.
> Allowed output transports are lat pad v120 mop
> telnet rlogin nasi ssh.
> Preferred transport is lat.
> No output characters are padded
> No special data dispatching characters
>
>
>
>
> Thanks
>
> Larry Roberts CCNP
> Expanets
> 5520 West 76th St.
> Indianapolis IN 46278
> 317.870.2550 Office
> 317.402.9730 Cell
> 813.655.2491 Fax
>
This archive was generated by hypermail 2.1.4 : Mon Oct 07 2002 - 07:43:49 GMT-3