From: CCIE FUN (ccieexam2002@xxxxxxxxx)
Date: Thu Aug 15 2002 - 00:01:31 GMT-3
Dmitry
Please define a map-class under the global config of
the router
use the following command
map-class frame-relay "NAME OF THE MAP-CLASS
then you will enter into the map-class config mode.
under that mode, you can enter the frame-relay
commands.
once done.
then go to the appropriate sub-interface where you
want to apply the traffic shaping and
there are two ways you could do it
1st one is described in previous email.
2nd one is to just enter the following command
frame-relay class " the class name you defined
previously"
using this config ensures that FRTS is only applied to
the required interface.
hoep that helps
--- "Volkov, Dmitry (Toronto - BCE)"
<dmitry_volkov@ca.ml.com> wrote:
> Hello,
>
> There is nothing special in config:
>
> r1#sh run int s0/0
> Building configuration...
>
> Current configuration : 113 bytes
> !
> interface Serial0/0
> no ip address
> encapsulation frame-relay
> no fair-queue
> frame-relay traffic-shaping
> end
>
> r1#sh run int s0/0.1
> Building configuration...
>
> Current configuration : 122 bytes
> !
> interface Serial0/0.1 multipoint
> ip address 133.10.6.1 255.255.255.0
> frame-relay map ip 133.10.6.2 110 broadcast
> end
>
> r1#sh run int s0/0.23
> Building configuration...
>
> Current configuration : 170 bytes
> !
> interface Serial0/0.23 multipoint
> ip address 133.10.1.3 255.255.255.224
> frame-relay map ip 133.10.1.4 120 broadcast
> frame-relay map ip 133.10.1.6 130 broadcast
> end
>
> r1#sh traffic-shape
>
> Interface Se0/0.1
> Access Target Byte Sustain Excess
> Interval Increment Adapt
> VC List Rate Limit bits/int bits/int
> (ms) (bytes)
> Active
> 110 56000 875 7000 0
> 125 875 -
>
> Interface Se0/0.23
> Access Target Byte Sustain Excess
> Interval Increment Adapt
> VC List Rate Limit bits/int bits/int
> (ms) (bytes)
> Active
> 120 56000 875 7000 0
> 125 875 -
> 130 56000 875 7000 0
> 125 875 -
> r1#
>
> So,
> CCO
>
http://www.cisco.com/warp/customer/125/traffic_shaping_6151.html
> said
> Frame-relay traffic shaping is enabled on the main
> interface, and it applies
> to all DLCIs under that interface. We cannot enable
> traffic shaping only for
> a particular DLCI or subinterface under the main
> interface. If a certain
> DLCI has no map class attached to it, and traffic
> shaping is enabled on the
> main interface, the DLCI is assigned a default
> map-class with CIR = 56000.
>
> So, If I enabled FRTS under physical interface I got
> default map class with
> CIR=56000 on all DLCI / subinterfaces
> I see only one way to complete Darth Reid lab
> reguirement: (but this is
> called GTS not FRTS)
> to enable GTS on s0/0.1 subinterface:
>
> interface Serial0/0
> no frame-relay traffic-shaping
> interface Serial0/0.1 multipoint
> ip address 133.10.6.1 255.255.255.0
> traffic-shape rate 64000 8000 8000 1000
> traffic-shape adaptive 32000
> frame-relay map ip 133.10.6.2 110 broadcast
>
> r1#sh traffic-shape
>
> Interface Se0/0.1
> Access Target Byte Sustain Excess
> Interval Increment Adapt
> VC List Rate Limit bits/int bits/int
> (ms) (bytes)
> Active
> VC List Rate Limit bits/int bits/int
> (ms) (bytes)
> Active
>
> Dmitry
>
> -----Original Message-----
> From: CCIE FUN [mailto:ccieexam2002@yahoo.com]
> Sent: Tuesday, August 13, 2002 2:51 PM
> To: Volkov, Dmitry (Toronto - BCE)
> Cc: 'ccielab@groupstudy.com'
> Subject: RE: FRTS Solie Darth Reid
>
>
> Can i look at your config please
>
> thanks
>
>
> --- "Volkov, Dmitry (Toronto - BCE)"
> <dmitry_volkov@ca.ml.com> wrote:
> > Hi FUN,
> >
> > As soon as You applied FRTS on major interface You
> > already have default
> > map-class.
> > You can override the default for specific DLCI on
> a
> > specific subint by using
> > frame-relay
> > class VC config command to assign the DLCI
> > explicitly to a different class.
> >
> >
> > r1(config)#int s0/0
> > r1(config-if)#fr
> > r1(config-if)#fram
> > r1(config-if)#frame-relay tr
> > r1(config-if)#frame-relay traf
> > r1(config-if)#frame-relay traffic-shaping
> > r1(config-if)#^Z
> > r1#sh run int s0/0.1
> > 08:19:24: %SYS-5-CONFIG_I: Configured from console
> > by console
> > r1#sh traffic-shape
> >
> > Interface Se0/0.1
> > Access Target Byte Sustain Excess
> > Interval Increment Adapt
> > VC List Rate Limit bits/int bits/int
> > (ms) (bytes)
> > Active
> > 110 56000 875 7000 0
> > 125 875 -
> >
> > Interface Se0/0.2
> > Access Target Byte Sustain Excess
> > Interval Increment Adapt
> > VC List Rate Limit bits/int bits/int
> > (ms) (bytes)
> > Active
> > 120 56000 875 7000 0
> > 125 875 -
> > 130 56000 875 7000 0
> > 125 875 -
> > r1#
> >
> > I don't have to have FRTS on S0/0.2 (VC 120, 130)
> > but I get it as soon as I
> > applied FRTS on major interface.
> >
> > Dmitry
> >
> >
> > -----Original Message-----
> > From: CCIE FUN [mailto:ccieexam2002@yahoo.com]
> > Sent: Monday, August 12, 2002 4:44 PM
> > To: Volkov, Dmitry (Toronto - BCE);
> > 'ccielab@groupstudy.com'
> > Subject: Re: FRTS Solie Darth Reid
> >
> >
> > you apply FRTS map-class on a per DLCI basis.
> >
> > under the s0.1
> > possibly you must have used the command
> >
> > frame-relay interface dlci 110
> >
> > that is when you enter the "Frame Relay DLCI
> > interface configuration mode "
> >
> > you could then relate the map-class under this
> mode
> >
> > with the following command
> >
> > class "class name"
> >
> > this command only configures the map-class under
> the
> > specified interface and does not interfere with
> s0.2
>
=== message truncated ===
This archive was generated by hypermail 2.1.4 : Sat Sep 07 2002 - 19:48:25 GMT-3