From: CCIE FUN (ccieexam2002@xxxxxxxxx)
Date: Tue Aug 13 2002 - 15:51:25 GMT-3
Can i look at your config please
thanks
--- "Volkov, Dmitry (Toronto - BCE)"
<dmitry_volkov@ca.ml.com> wrote:
> Hi FUN,
>
> As soon as You applied FRTS on major interface You
> already have default
> map-class.
> You can override the default for specific DLCI on a
> specific subint by using
> frame-relay
> class VC config command to assign the DLCI
> explicitly to a different class.
>
>
> r1(config)#int s0/0
> r1(config-if)#fr
> r1(config-if)#fram
> r1(config-if)#frame-relay tr
> r1(config-if)#frame-relay traf
> r1(config-if)#frame-relay traffic-shaping
> r1(config-if)#^Z
> r1#sh run int s0/0.1
> 08:19:24: %SYS-5-CONFIG_I: Configured from console
> by console
> r1#sh traffic-shape
>
> Interface Se0/0.1
> Access Target Byte Sustain Excess
> Interval Increment Adapt
> VC List Rate Limit bits/int bits/int
> (ms) (bytes)
> Active
> 110 56000 875 7000 0
> 125 875 -
>
> Interface Se0/0.2
> Access Target Byte Sustain Excess
> Interval Increment Adapt
> VC List Rate Limit bits/int bits/int
> (ms) (bytes)
> Active
> 120 56000 875 7000 0
> 125 875 -
> 130 56000 875 7000 0
> 125 875 -
> r1#
>
> I don't have to have FRTS on S0/0.2 (VC 120, 130)
> but I get it as soon as I
> applied FRTS on major interface.
>
> Dmitry
>
>
> -----Original Message-----
> From: CCIE FUN [mailto:ccieexam2002@yahoo.com]
> Sent: Monday, August 12, 2002 4:44 PM
> To: Volkov, Dmitry (Toronto - BCE);
> 'ccielab@groupstudy.com'
> Subject: Re: FRTS Solie Darth Reid
>
>
> you apply FRTS map-class on a per DLCI basis.
>
> under the s0.1
> possibly you must have used the command
>
> frame-relay interface dlci 110
>
> that is when you enter the "Frame Relay DLCI
> interface configuration mode "
>
> you could then relate the map-class under this mode
>
> with the following command
>
> class "class name"
>
> this command only configures the map-class under the
> specified interface and does not interfere with s0.2
> you should not see any config commands generated
> automatically under s0.2
>
> hope that helps
>
>
> --- "Volkov, Dmitry (Toronto - BCE)"
> <dmitry_volkov@ca.ml.com> wrote:
> > Hi,
> >
> > I'm trying to do Solie's Darth Reid lab and I
> can't
> > get FRTS working.
> > According to Lab requirement (page 1149 sect III,
> > i.4):
> > "Configure FRTS on the PVC between R1 & R2 so that
> > it responds to BECNS....,
> > etc"
> >
> > R1 has one major serial 0 with two multipoint
> > subinterfaces s0.1 and s0.2
> > s0.1 has PVC 110 to R2, s0.2 has PVCs 120 and 130
> > to the other routes via
> > cloud.
> >
> > So I enabled FRTS on major interface and
> configured
> > map-class and applied
> > it to s0.1 (there is only one DLCI there).
> > The same time doing like that I get default FRTS
> > class-map on s0.2 with CIR
> > 56000, etc.
> >
> > So I don't understand how it is possible to
> > "disable" FRTS on other subint
> > or particular DLCIs..
> >
> > I can configure GTS on subint basis but not FRTS,
> >
> > Did I miss something or Lab requirement is not
> > correct ?
> >
> >
> > Thanks,
> >
> > Dmitry
> >
>
This archive was generated by hypermail 2.1.4 : Sat Sep 07 2002 - 19:48:24 GMT-3