From: Volkov, Dmitry (Toronto - BCE) (dmitry_volkov@xxxxxxxxx)
Date: Tue Aug 13 2002 - 14:30:33 GMT-3
Hello group,
Can somebody clarify on it finally ?????
1st Question:==========
FRTS: 1)frame-relay CIR ; 2)frame relay MinCIR
GTS: 3)traffic-shape rate CIR
Is CIR from command 3) the same as CIR from command 1) ???
Or it has to be interpreted as MiCir (i.e. rate guaranteed rate obtained
from provider) ???
2nd Question:==========
What CIR You have to configure on Central site if You have Central site
1544000 and remote 64000 ????
CCO says: http://www.cisco.com/warp/customer/125/21.shtml
"If the central side has a upper limit of 256 kbps, you should use the
LOWEST upper limit value"
Solie and some other guys (i.e. MADMAN) tell "set CIR to be the phisycal
port speed of the circuit at Central site"
I did look at archives this year and didn't find any good explanation .....
3rd Question: ==========
According to
http://www.cisco.com/warp/customer/125/traffic_shaping_6151.html and Solie :
Be (excess burst) is the number of excess bits to transmit during the FIRST
(???) interval (Tc) over and above Bc, once credit is built up.
How Be has to be calculated, when we place Be under "frame-relay be" command
:
How many bits can be send over bc per Tc ?? or How many bits can we send
over CIR during 1 second (i.e. spread in time) ??????
The difference is 8 times if Tc=125 ms !
Solie example: He did put Be 64000 on page 368 and 398 (so it doesn't look
like typo) - I absolutely don't understand this.
Please explain that !!!
CCO http://www.cisco.com/warp/customer/125/21.shtml said: PEAK = DLCI
maximum speed = (Bc+Be)/Tc = CIR + Be/Tc = AR
if be=64000 sec and bc =8000 sec that is mean that AR = 576000bits/sec but
he mentioned that circuit on the far end only 64K.
http://www.cisco.com/warp/customer/125/traffic_shaping_6151.html gives the
following example:
Circuit speed 192 K, Bc =8000 ; Tc=125 CIR 6400 ====> Be =192000/8 - 8000
i.e. We can send 16000 bits over Bc 8000 bits during TC only (which is equal
rate 192K) !
4th Question: ==========
CCO http://www.cisco.com/warp/customer/125/traffic_shaping_6151.html said
Frame-relay traffic shaping is enabled on the main interface, and it applies
to all DLCIs under that interface. We cannot enable traffic shaping only for
a particular DLCI or subinterface under the main interface. If a certain
DLCI has no map class attached to it, and traffic shaping is enabled on the
main interface, the DLCI is assigned a default map-class with CIR = 56000.
So, If I enabled FRTS under physical interface I got default map class with
CIR=56000 on all DLCI / subinterfaces
What if I have 100 DLCs/suniterfaces and I want to implement shaping only on
some of them ??
How to do it ???
I see only one way to do it: put DLCIs where I want to implemet shaping
under particular subinterface and enable GTS on this subint.
Any comments ???
Thanks
Dmitry
This archive was generated by hypermail 2.1.4 : Sat Sep 07 2002 - 19:48:24 GMT-3