From: dwclemons (dwclemons@xxxxxxx)
Date: Sat Jul 20 2002 - 15:06:51 GMT-3
Brian, were you able to ping the 195.1.3.3 loopback address from r6, or is
that part of the requirement?
Thanks
----- Original Message -----
From: "Perminder Grewal" <percy_gunner@hotmail.com>
To: <brian@cyscoexpert.com>; <ipsec@myrealbox.com>; <ccielab@groupstudy.com>
Sent: Saturday, July 20, 2002 6:38 AM
Subject: RE: Re: Cyscoexpert Official Configs
> I have had an attempt on this lab and would like to post some issues to
the
> group to resolve some of them.
>
> C.2) I made the subnet for 150.1.222.0/24 a non-broadcast network to
change
> the timers; however I put in full-mesh neighbour statements as you would
do
> for a frame-relay network. Is this OK?
>
> D.1) I know you changed the RIP timers on the IP Cloud to 10 60 60 80. I
> made it 10 30 30 40 i.e. 3 times the update interval as this is the
baseline
> for RIP. I did various debugs and could not verify the timers from the IP
> Cloud. Is there a way to do this or am I digging to deep on this issue.
>
> E.3) One-way redistribution from rip to eigrp, also mutual redistribution
> between ospf and eigrp. I used tags to avoid routing loops as shown below
>
> router eigrp 100
> Redistribute ospf 1 metric 1000 100 255 1 1500 route-map tag11_2_ospf
>
> router ospf 1
> Redistribute eigrp 100 subnets tag 11
>
>
> Route-map tag11_2_ospf deny 10
> match tag 11
>
> route-map tag11_2_ospf permit 20
>
> Is this ok?
>
>
> The biggest challenge was getting all the routes in R1. I had the routes
in
> the eigrp topology table as Inaccessible due to AD of 170 and Ospf 110.
I
> changed the distance of all the ospf routes to 171 on R4 and the eigrp
> routes came in on R4 and R1 via the tunnel, However my tunnel started to
> bounce due to "recursive lookup" and the routes toggled between ospf and
> eigrp. The only route that I could not see on R1 was 150.1.30.0/24 from
R3.
> So I set up an accesss-list and changed the distance as shown below
>
> router ospf 1
> distance 171 0.0.0.0 255.255.255.255 1
>
> access-list 1 permit 150.1.30.0
>
>
> I found the following link about the recursive lookup.
>
> http://www.cisco.com/warp/public/105/gre_flap.html
>
> The external eigrp routes are propagated down the tunnel from R2 to R4 and
> enter the route table with AD off (EX) 170, however these routes get
flushed
> as ospf has the same prefixes with AD of 110. This bounces the tunnel up
and
> down every time the route table is refreshed between eigrp and ospf. Is
my
> understanding of this correct?
>
>
> Cheers
>
> Percy
>
>
>
>
>
>
> >From: "Brian McGahan" <brian@cyscoexpert.com>
> >Reply-To: "Brian McGahan" <brian@cyscoexpert.com>
> >To: "'IPSec'" <ipsec@myrealbox.com>, <ccielab@groupstudy.com>
> >Subject: RE: Re: Cyscoexpert Official Configs
> >Date: Sun, 14 Jul 2002 15:04:02 -0500
> >
> > Regarding the 150.1.30.0/24 on R1, if you followed the
> >directions carefully there is no way to learn it via OSPF. Area 12
> >should be either a stub area or an NSSA. If it is a stub area, R1
> >should be filtering out the default route he's learning from R2 so that
> >it doesn't appear in the table. NSSA doesn't generate a default route
> >by default.
> >
> > Since R3's Ethernet (30.0/24) should be advertised "without
> >using the network statement", you have to redistribute connected. When
> >you redistribute connected, this route now becomes a type 5 external
> >LSA. Both stub and NSSA areas do not allow type 5 LSA, therefore it
> >cannot be learned via OSPF. R1's only option to learn this route is now
> >via EIGRP.
> >
> > This now presents another problem, which is EIGRP's calculation
> >of route feasibility. If you have a duplicate longest match through
> >another protocol with a lower administrative distance than EIGRP, EIGRP
> >will not consider its own route feasible. The only solution here then
> >is to change the distance of the 30.0/24 route on R4 to make EIGRP have
> >the preferred administrative distance.
> >
> > Also, we run into the issue here that you cannot change the
> >distance of an EIGRP external route on a per route basis. We could
> >solve this problem by changing *all* external EIGRP routes to have a
> >distance less than 110, however this is a sloppy solution.
> >
> > Therefore my preferred solution is to raise the distance of the
> >OSPF route to be above 170. You can change the distance on a per route
> >basis, and it will not affect other path determinations.
> >
> > Tada! R1 now has reachability to 150.1.30.0/24 via EIGRP.
> >
> >HTH
> >
> >Brian McGahan, CCIE #8593
> >Director of Design and Implementation
> >brian@cyscoexpert.com
> >
> >CyscoExpert Corporation
> >Internetwork Consulting & Training
> >http://www.cyscoexpert.com
> >Voice: 847.674.3392
> >Fax: 847.674.2625
> >
> >
> >-----Original Message-----
> >From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
> >IPSec
> >Sent: Sunday, July 14, 2002 1:39 AM
> >To: nshah@connect.com.au
> >Cc: ccielab@groupstudy.com
> >Subject: Re: Re: Cyscoexpert Official Configs
> >
> >Since 150.1.30.0/24 is an E2 network in OSPF, it's not allowed in R1.
> >150.1.30.0/24 gets in R1's routing table by EIGRP from redistribution
> >from OSPF.
> >
> >
> >-----Original Message-----
> >From: "Nick Shah" <nshah@connect.com.au>
> >To: "IPSec" <ipsec@myrealbox.com>, <ccielab@groupstudy.com>
> >Date: Sun, 14 Jul 2002 16:21:13 +1000
> >Subject: Re: Cyscoexpert Official Configs
> >
> >And how did u get 150.1.30.0/24 into R1 's routing table (via OSPF) ?
> >
> >Nick
> >----- Original Message -----
> >From: IPSec <ipsec@myrealbox.com>
> >To: <ccielab@groupstudy.com>
> >Sent: Sunday, July 14, 2002 3:12 PM
> >Subject: Cyscoexpert Official Configs
> >
> >
> > > Hi Group,
> > >
> > > Here are the official lab solutions:
> > >
> > > TermServ-34>1
> > > [Resuming connection 1 to rack3r1 ... ]
> > >
> > > R1#sh run
> > > Building configuration...
> > >
> > >
> > >
> > > Current configuration : 2014 bytes
> > > !
> > > version 12.1
> > > service timestamps debug uptime
> > > service timestamps log uptime
> > > no service password-encryption
> > > !
> > > hostname R1
> > > !
> > > enable password cisco
> > > !
> > > !
> > > !
> > > !
> > > !
> > > ip subnet-zero
> > > no ip domain-lookup
> > > !
> > > ipx routing 0001.0001.0001
> > > !
> > > !
> > > dlsw local-peer peer-id 150.1.1.1
> > > dlsw remote-peer 0 tcp 150.1.3.3
> > > dlsw icanreach mac-exclusive
> > > dlsw icanreach mac-address 7145.a0e3.0000 mask ffff.ffff.0000
> > > dlsw bridge-group 1
> > > !
> > > interface Loopback0
> > > ip address 150.1.1.1 255.255.255.0
> > > ipx network 1
> > > !
> > > interface Loopback1
> > > ip address 220.1.0.1 255.255.255.0
> > > !
> > > interface Loopback2
> > > ip address 220.1.1.1 255.255.255.0
> > > !
> > > interface Loopback3
> > > ip address 220.1.2.1 255.255.255.0
> > > !
> > > interface Loopback4
> > > ip address 220.1.3.1 255.255.255.0
> > > !
> > > interface Loopback10
> > > ip address 195.1.1.1 255.255.255.0
> > > !
> > > interface Ethernet0
> > > ip address 150.1.10.1 255.255.255.0
> > > ipx network 10
> > > bridge-group 1
> > > !
> > > interface Serial0
> > > ip address 150.1.14.1 255.255.255.0
> > > ip summary-address eigrp 100 220.1.0.0 255.255.252.0 5
> > > ipx network 14
> > > no fair-queue
> > > clockrate 2000000
> > > !
> > > interface Serial1
> > > ip address 150.1.12.1 255.255.255.0
> > > ipx network 12
> > > clockrate 2000000
> > > !
> > > interface TokenRing0
> > > no ip address
> > > shutdown
> > > !
> > > router eigrp 100
> > > network 150.1.14.1 0.0.0.0
> > > network 220.1.0.0 0.0.3.255
> > > auto-summary
> > > no eigrp log-neighbor-changes
> > > !
> > > router ospf 1
> > > router-id 150.1.1.1
> > > log-adjacency-changes
> > > area 12 nssa
> > > network 150.1.1.1 0.0.0.0 area 12
> > > network 150.1.12.1 0.0.0.0 area 12
> > > !
> > > router bgp 1
> > > bgp log-neighbor-changes
> > > network 195.1.1.0
> > > neighbor 150.1.12.2 remote-as 256
> > > neighbor 150.1.14.4 remote-as 34
> > > neighbor 150.1.14.4 route-map PREPEND out
> > > !
> > > ip classless
> > > ip http server
> > > !
> > > !
> > > ip prefix-list R1_LOOPBACK seq 5 permit 195.1.1.0/24
> > > route-map PREPEND permit 10
> > > match ip address prefix-list R1_LOOPBACK
> > > set as-path prepend 1 1
> > > !
> > > route-map PREPEND permit 20
> > > !
> > > !
> > > !
> > > !
> > > !
> > > bridge 1 protocol ieee
> > > !
> > > line con 0
> > > exec-timeout 0 0
> > > logging synchronous
> > > line aux 0
> > > exec-timeout 0 0
> > > logging synchronous
> > > line vty 0 4
> > > exec-timeout 0 0
> > > logging synchronous
> > > no login
> > > !
> > > end
> > >
> > > R1#
> > > TermServ-34>2
> > > [Resuming connection 2 to rack3r2 ... ]
> > >
> > > R2#sh run
> > > Building configuration...
> > >
> > > Current configuration : 2171 bytes
> > > !
> > > version 12.1
> > > service timestamps debug uptime
> > > service timestamps log uptime
> > > no service password-encryption
> > > !
> > > hostname R2
> > > !
> > > enable password cisco
> > > !
> > > !
> > > !
> > > !
> > > !
> > > ip subnet-zero
> > > no ip domain-lookup
> > > !
> > > ipx routing 0002.0002.0002
> > > ipx internal-network 2222
> > > !
> > > !
> > > !
> > > interface Loopback0
> > > ip address 150.1.2.2 255.255.255.0
> > > ipx network 2
> > > !
> > > interface Loopback10
> > > ip address 195.1.2.2 255.255.255.0
> > > !
> > > interface Tunnel0
> > > ip address 150.1.24.2 255.255.255.0
> > > ipx network 24
> > > tunnel source Loopback0
> > > tunnel destination 150.1.4.4
> > > !
> > > interface Ethernet0
> > > ip address 150.1.222.2 255.255.255.0
> > > no ip redirects
> > > ip ospf message-digest-key 1 md5 cisco
> > > ip ospf network point-to-multipoint
> > > ipx network 222
> > > ipx nlsp enable
> > > standby 1 ip 150.1.222.1
> > > standby 1 priority 50
> > > standby 1 preempt
> > > standby 1 track Serial0 50
> > > !
> > > interface Serial0
> > > ip address 150.1.12.2 255.255.255.0
> > > ipx network 12
> > > no fair-queue
> > > !
> > > interface Serial1
> > > no ip address
> > > shutdown
> > > !
> > > router eigrp 100
> > > redistribute ospf 1 metric 1 1 1 1 1
> > > network 150.1.24.2 0.0.0.0
> > > auto-summary
> > > no eigrp log-neighbor-changes
> > > !
> > > router ospf 1
> > > router-id 150.1.2.2
> > > log-adjacency-changes
> > > area 0 authentication
> > > area 12 nssa
> > > area 51 authentication message-digest
> > > area 51 virtual-link 150.1.5.5 authentication-key cisco
> > > redistribute eigrp 100 subnets
> > > network 150.1.2.2 0.0.0.0 area 51
> > > network 150.1.12.2 0.0.0.0 area 12
> > > network 150.1.222.2 0.0.0.0 area 51
> > > !
> > > router bgp 256
> > > no synchronization
> > > bgp log-neighbor-changes
> > > network 195.1.2.0
> > > neighbor 150.1.4.4 remote-as 34
> > > neighbor 150.1.4.4 ebgp-multihop 255
> > > neighbor 150.1.4.4 update-source Loopback0
> > > neighbor 150.1.12.1 remote-as 1
> > > neighbor 150.1.12.1 route-map LOCALPREF in
> > > neighbor 150.1.222.6 remote-as 256
> > > !
> > > ip classless
> > > ip http server
> > > !
> > > !
> > > ip prefix-list R3_LOOPBACK seq 5 permit 195.1.3.0/24
> > > route-map LOCALPREF permit 10
> > > match ip address prefix-list R3_LOOPBACK
> > > set local-preference 200
> > > !
> > > route-map LOCALPREF permit 20
> > > !
> > > !
> > > !
> > > !
> > > ipx router nlsp
> > > area-address 0 0
> > > !
> > > !
> > > ipx router rip
> > > no network 222
> > > !
> > > !
> > > !
> > > !
> > > line con 0
> > > exec-timeout 0 0
> > > logging synchronous
> > > line aux 0
> > > exec-timeout 0 0
> > > logging synchronous
> > > line vty 0 4
> > > exec-timeout 0 0
> > > logging synchronous
> > > no login
> > > !
> > > end
> > >
> > > R2#
> > > TermServ-34>3
> > > [Resuming connection 3 to rack3r3 ... ]
> > >
> > > R3#sh run
> > > Building configuration...
> > >
> > >
> > >
> > > Current configuration : 1973 bytes
> > > !
> > > version 12.1
> > > service timestamps debug uptime
> > > service timestamps log uptime
> > > no service password-encryption
> > > !
> > > hostname R3
> > > !
> > > enable password cisco
> > > !
> > > !
> > > !
> > > !
> > > !
> > > ip subnet-zero
> > > no ip domain-lookup
> > > !
> > > ipx routing 0003.0003.0003
> > > !
> > > !
> > > dlsw local-peer peer-id 150.1.3.3
> > > dlsw remote-peer 0 tcp 150.1.1.1
> > > dlsw remote-peer 0 frame-relay interface Serial0 304
> > > dlsw icannotreach sap F0
> > > dlsw bridge-group 1
> > > !
> > > interface Loopback0
> > > ip address 150.1.3.3 255.255.255.0
> > > ipx network 3
> > > !
> > > interface Loopback10
> > > ip address 195.1.3.3 255.255.255.0
> > > !
> > > interface Serial0
> > > ip address 150.1.111.3 255.255.255.248
> > > encapsulation frame-relay
> > > ip ospf authentication-key cisco
> > > ip ospf priority 255
> > > ipx network 111
> > > no ipx split-horizon eigrp 11
> > > no arp frame-relay
> > > frame-relay map llc2 304 broadcast
> > > frame-relay map ip 150.1.111.4 304 broadcast
> > > frame-relay map ip 150.1.111.5 305 broadcast
> > > frame-relay map ipx 111.0004.0004.0004 304 broadcast
> > > frame-relay map ipx 111.0005.0005.0005 305 broadcast
> > > no frame-relay inverse-arp
> > > frame-relay lmi-type cisco
> > > !
> > > interface Serial1
> > > no ip address
> > > shutdown
> > > !
> > > interface Ethernet0
> > > ip address 150.1.30.3 255.255.255.0
> > > ipx network 30
> > > bridge-group 1
> > > !
> > > interface BRI0
> > > no ip address
> > > shutdown
> > > isdn x25 static-tei 0
> > > !
> > > router ospf 1
> > > router-id 150.1.3.3
> > > log-adjacency-changes
> > > area 0 authentication
> > > redistribute connected subnets route-map CONNECTED
> > > network 150.1.3.3 0.0.0.0 area 0
> > > network 150.1.111.3 0.0.0.0 area 0
> > > neighbor 150.1.111.5
> > > neighbor 150.1.111.4
> > > !
> > > router bgp 34
> > > no synchronization
> > > bgp log-neighbor-changes
> > > network 195.1.3.0
> > > neighbor 150.1.111.4 remote-as 34
> > > !
> > > ip classless
> > > ip http server
> > > !
> > > route-map CONNECTED permit 10
> > > match interface Ethernet0
> > > !
> > > !
> > > !
> > > !
> > > ipx router eigrp 11
> > > network 111
> > > !
> > > !
> > > ipx router rip
> > > no network 111
> > > !
> > > !
> > > !
> > > bridge 1 protocol ieee
> > > !
> > > line con 0
> > > exec-timeout 0 0
> > > logging synchronous
> > > line aux 0
> > > exec-timeout 0 0
> > > logging synchronous
> > > line vty 0 4
> > > exec-timeout 0 0
> > > logging synchronous
> > > no login
> > > !
> > > end
> > >
> > > R3#
> > > TermServ-34>4
> > > [Resuming connection 4 to rack3r4 ... ]
> > >
> > > R4#sh run
> > > Building configuration...
> > >
> > >
> > >
> > > Current configuration : 3401 bytes
> > > !
> > > version 12.1
> > > service timestamps debug uptime
> > > service timestamps log uptime
> > > no service password-encryption
> > > !
> > > hostname R4
> > > !
> > > enable password cisco
> > > !
> > > !
> > > !
> > > !
> > > !
> > > ip subnet-zero
> > > no ip domain-lookup
> > > !
> > > ipx routing 0004.0004.0004
> > > !
> > > !
> > > dlsw local-peer peer-id 150.1.4.4
> > > dlsw remote-peer 0 frame-relay interface Serial0 403
> > > dlsw bridge-group 1
> > > !
> > > interface Loopback0
> > > ip address 150.1.4.4 255.255.255.0
> > > ipx network 4
> > > !
> > > interface Loopback10
> > > ip address 195.1.4.4 255.255.255.0
> > > !
> > > interface Tunnel0
> > > ip address 150.1.24.4 255.255.255.0
> > > ipx network 24
> > > ipx output-sap-filter 1001
> > > tunnel source Loopback0
> > > tunnel destination 150.1.2.2
> > > !
> > > interface Ethernet0
> > > ip address 170.1.1.1 255.255.255.0
> > > ipx input-sap-filter 1000
> > > ipx network 1000
> > > bridge-group 1
> > > !
> > > interface Serial0
> > > ip address 150.1.111.4 255.255.255.248
> > > encapsulation frame-relay
> > > ip ospf authentication-key cisco
> > > ip ospf priority 0
> > > ipx network 111
> > > ipx output-sap-filter 1001
> > > no arp frame-relay
> > > frame-relay map llc2 403 broadcast
> > > frame-relay map ip 150.1.111.3 403 broadcast
> > > frame-relay map ip 150.1.111.5 403 broadcast
> > > frame-relay map ipx 111.0003.0003.0003 403 broadcast
> > > frame-relay map ipx 111.0005.0005.0005 403 broadcast
> > > no frame-relay inverse-arp
> > > frame-relay lmi-type cisco
> > > !
> > > interface Serial1
> > > ip address 150.1.14.4 255.255.255.0
> > > ipx network 14
> > > ipx output-sap-filter 1001
> > > !
> > > interface BRI0
> > > no ip address
> > > shutdown
> > > isdn x25 static-tei 0
> > > !
> > > router eigrp 100
> > > redistribute rip metric 1 1 1 1 1
> > > network 150.1.14.4 0.0.0.0
> > > network 150.1.24.4 0.0.0.0
> > > auto-summary
> > > no eigrp log-neighbor-changes
> > > !
> > > router ospf 1
> > > router-id 150.1.4.4
> > > log-adjacency-changes
> > > area 0 authentication
> > > redistribute rip subnets route-map RIP2OSPF
> > > network 150.1.4.4 0.0.0.0 area 0
> > > network 150.1.111.4 0.0.0.0 area 0
> > > distance 171 0.0.0.0 255.255.255.255 1
> > > !
> > > router rip
> > > timers basic 10 60 60 80
> > > network 170.1.0.0
> > > !
> > > router bgp 34
> > > no synchronization
> > > bgp log-neighbor-changes
> > > network 195.1.4.0
> > > neighbor 150.1.2.2 remote-as 256
> > > neighbor 150.1.2.2 ebgp-multihop 255
> > > neighbor 150.1.2.2 update-source Loopback0
> > > neighbor 150.1.2.2 route-map MED out
> > > neighbor 150.1.14.1 remote-as 1
> > > neighbor 150.1.14.1 route-map MED out
> > > neighbor 150.1.111.3 remote-as 34
> > > neighbor 150.1.111.3 route-map MED out
> > > neighbor 170.1.1.254 remote-as 100
> > > neighbor 170.1.1.254 route-map NO-EXPORT in
> > > !
> > > ip classless
> > > ip http server
> > > ip as-path access-list 1 permit _1000_
> > > ip as-path access-list 2 permit ^100_
> > > !
> > > !
> > > ip access-list standard EVEN_SECOND_OCTET
> > > permit 0.0.0.0 255.254.255.255
> > > ip access-list standard ODD_THIRD_OCTET
> > > permit 0.0.1.0 255.255.254.255
> > > access-list 1 permit 150.1.30.0
> > > access-list 1000 deny FFFFFFFF 4
> > > access-list 1000 permit FFFFFFFF
> > > access-list 1001 deny 1.0000.0000.0000 FFFFFFFE.ffff.ffff.ffff 7
> > > access-list 1001 permit FFFFFFFF
> > > route-map NO-EXPORT permit 10
> > > match as-path 1
> > > set community no-export
> > > !
> > > route-map NO-EXPORT permit 20
> > > !
> > > route-map MED permit 10
> > > match ip address ODD_THIRD_OCTET
> > > match as-path 2
> > > set metric 31337
> > > !
> > > route-map MED permit 20
> > > !
> > > route-map RIP2OSPF permit 10
> > > match ip address EVEN_SECOND_OCTET
> > > set metric 1000
> > > !
> > > route-map RIP2OSPF permit 20
> > > set metric-type type-1
> > > !
> > > !
> > > !
> > > !
> > > ipx router eigrp 11
> > > network 111
> > > !
> > > !
> > > ipx router rip
> > > no network 111
> > > !
> > > !
> > > !
> > > bridge 1 protocol ieee
> > > !
> > > line con 0
> > > exec-timeout 0 0
> > > logging synchronous
> > > line aux 0
> > > exec-timeout 0 0
> > > logging synchronous
> > > line vty 0 4
> > > exec-timeout 0 0
> > > logging synchronous
> > > no login
> > > !
> > > end
> > >
> > > R4#
> > > TermServ-34>5
> > > [Resuming connection 5 to rack3r5 ... ]
> > >
> > > R5#sh run
> > > Building configuration...
> > >
> > > Current configuration : 2019 bytes
> > > !
> > > version 12.1
> > > service timestamps debug uptime
> > > service timestamps log uptime
> > > no service password-encryption
> > > !
> > > hostname R5
> > > !
> > > enable password cisco
> > > !
> > > !
> > > !
> > > !
> > > !
> > > ip subnet-zero
> > > no ip domain-lookup
> > > !
> > > ipx routing 0005.0005.0005
> > > ipx internal-network 5555
> > > !
> > > !
> > > !
> > > interface Loopback0
> > > ip address 150.1.5.5 255.255.255.0
> > > ipx network 5
> > > !
> > > interface Loopback10
> > > ip address 195.1.5.5 255.255.255.0
> > > !
> > > interface Ethernet0
> > > ip address 150.1.222.5 255.255.255.0
> > > no ip redirects
> > > ip ospf message-digest-key 1 md5 cisco
> > > ip ospf network point-to-multipoint
> > > ipx network 222
> > > ipx nlsp enable
> > > standby 1 ip 150.1.222.1
> > > standby 1 preempt
> > > standby 1 track Serial0 100
> > > !
> > > interface Serial0
> > > ip address 150.1.111.5 255.255.255.248
> > > encapsulation frame-relay
> > > ip ospf authentication-key cisco
> > > ip ospf priority 0
> > > ipx network 111
> > > no arp frame-relay
> > > frame-relay map ip 150.1.111.3 503 broadcast
> > > frame-relay map ip 150.1.111.4 503 broadcast
> > > frame-relay map ipx 111.0003.0003.0003 503 broadcast
> > > frame-relay map ipx 111.0004.0004.0004 503 broadcast
> > > no frame-relay inverse-arp
> > > frame-relay lmi-type cisco
> > > !
> > > interface Serial1
> > > no ip address
> > > shutdown
> > > !
> > > interface Serial2
> > > no ip address
> > > shutdown
> > > !
> > > interface Serial3
> > > no ip address
> > > shutdown
> > > !
> > > interface BRI0
> > > no ip address
> > > shutdown
> > > isdn x25 static-tei 0
> > > !
> > > router ospf 1
> > > router-id 150.1.5.5
> > > log-adjacency-changes
> > > area 0 authentication
> > > area 51 authentication message-digest
> > > area 51 virtual-link 150.1.2.2 authentication-key cisco
> > > network 150.1.5.5 0.0.0.0 area 0
> > > network 150.1.111.5 0.0.0.0 area 0
> > > network 150.1.222.5 0.0.0.0 area 51
> > > !
> > > router bgp 256
> > > no synchronization
> > > bgp log-neighbor-changes
> > > network 195.1.5.0
> > > neighbor 150.1.222.6 remote-as 256
> > > !
> > > ip classless
> > > ip http server
> > > !
> > > !
> > > !
> > > !
> > > ipx router eigrp 11
> > > network 111
> > > !
> > > !
> > > ipx router nlsp
> > > area-address 0 0
> > > !
> > > !
> > > ipx router rip
> > > no network 111
> > > no network 222
> > > !
> > > !
> > > !
> > > !
> > > line con 0
> > > exec-timeout 0 0
> > > logging synchronous
> > > line aux 0
> > > exec-timeout 0 0
> > > logging synchronous
> > > line vty 0 4
> > > exec-timeout 0 0
> > > logging synchronous
> > > no login
> > > !
> > > end
> > >
> > > R5#
> > > TermServ-34>6
> > > [Resuming connection 6 to rack3r6 ... ]
> > >
> > > R6#sh run
> > > Building configuration...
> > >
> > > Current configuration : 1945 bytes
> > > !
> > > version 12.1
> > > no service single-slot-reload-enable
> > > service timestamps debug uptime
> > > service timestamps log uptime
> > > no service password-encryption
> > > !
> > > hostname R6
> > > !
> > > logging rate-limit console 10 except errors
> > > enable password cisco
> > > !
> > > ip subnet-zero
> > > !
> > > !
> > > no ip finger
> > > no ip domain-lookup
> > > !
> > > ipx routing 0006.0006.0006
> > > ipx internal-network 6666
> > > call rsvp-sync
> > > cns event-service server
> > > !
> > > !
> > > !
> > > !
> > > !
> > > !
> > > !
> > > !
> > > interface Loopback0
> > > ip address 150.1.6.6 255.255.255.0
> > > ipx network 6
> > > !
> > > interface Loopback10
> > > ip address 195.1.6.6 255.255.255.0
> > > !
> > > interface BRI0/0
> > > no ip address
> > > shutdown
> > > !
> > > interface Ethernet0/0
> > > ip address 150.1.222.6 255.255.255.0
> > > ip ospf message-digest-key 1 md5 cisco
> > > ip ospf network point-to-multipoint
> > > half-duplex
> > > ipx network 222
> > > ipx nlsp enable
> > > standby 1 priority 25 preempt
> > > standby 1 ip 150.1.222.1
> > > !
> > > interface Serial0/0
> > > no ip address
> > > encapsulation frame-relay
> > > shutdown
> > > frame-relay lmi-type cisco
> > > !
> > > interface TokenRing0/0
> > > no ip address
> > > shutdown
> > > ring-speed 16
> > > !
> > > interface FastEthernet1/0
> > > no ip address
> > > shutdown
> > > duplex auto
> > > speed auto
> > > !
> > > interface ATM3/0
> > > no ip address
> > > shutdown
> > > no atm ilmi-keepalive
> > > !
> > > router ospf 1
> > > router-id 150.1.6.6
> > > log-adjacency-changes
> > > area 51 authentication message-digest
> > > network 150.1.6.6 0.0.0.0 area 51
> > > network 150.1.222.6 0.0.0.0 area 51
> > > !
> > > router bgp 256
> > > no synchronization
> > > bgp log-neighbor-changes
> > > network 195.1.6.0
> > > neighbor 150.1.222.2 remote-as 256
> > > neighbor 150.1.222.2 route-reflector-client
> > > neighbor 150.1.222.5 remote-as 256
> > > neighbor 150.1.222.5 route-reflector-client
> > > !
> > > ip kerberos source-interface any
> > > ip classless
> > > no ip http server
> > > !
> > > !
> > > !
> > > !
> > > ipx router nlsp
> > > area-address 0 0
> > > !
> > > !
> > > ipx router rip
> > > no network 222
> > > !
> > > !
> > > !
> > > !
> > > voice-port 2/0/0
> > > !
> > > voice-port 2/0/1
> > > !
> > > dial-peer cor custom
> > > !
> > > !
> > > !
> > > !
> > > line con 0
> > > exec-timeout 0 0
> > > logging synchronous
> > > transport input none
> > > line aux 0
> > > exec-timeout 0 0
> > > logging synchronous
> > > line vty 0 4
> > > exec-timeout 0 0
> > > logging synchronous
> > > no login
> > > !
> > > end
> > >
> > >
> > >
> > >
> > >
> > >
> > > > Guys,
> > > >
> > > > I have re created the configs for Cyscoexpert labs, since I was
> >getting
> > > > a
> > > > few queries. It would create havoc to send the config to the whole
> >group
> > > > (also, zipped or attachments are not supported).
> > > >
> > > > Can someone suggest if a similar service exists on Group study FTP
> > > > server
> > > > (if such a thing exists). Otherwise I will prolly upload it on one
> >of
> > > > the
> > > > free sites and post the url..
> > > >
> > > > The reason I want to do is to get the discussion on the ways other
> > > > people
> > > > have configged it, and I am also planning to suggest different ways
> > > > (where
> > > > possible) to acheive the same result.
> > > >
> > > > rgds
> > > > Nick
This archive was generated by hypermail 2.1.4 : Sat Sep 07 2002 - 19:36:37 GMT-3