From: kym blair (kymblair@xxxxxxxxxxx)
Date: Fri Jun 21 2002 - 18:17:02 GMT-3
Paul,
Config-register setting 0x1202 in binary is 0001 0010 0000 0010. Bit 0 is on
the right, bit 15 on the left. Your console speed is set to 1200 (bits 12
and 11 are set to "10"). By the way, your [BREAK] key will *NOT* be
disabled after bootup (bit 8 is set to "0").
If you set your console speed to 1200 baud, then reboot the router, you
should be able to interrupt the boot sequence with a [BREAK].
HTH, Kym
>From: "Wes Stevens" <ccie_miami@hotmail.com>
>Reply-To: "Wes Stevens" <ccie_miami@hotmail.com>
>To: p729@cox.net, ccielab@groupstudy.com
>Subject: Re: Please re- read a see can you help (More exact problem)
>Date: Fri, 21 Jun 2002 19:31:28 +0000
>
>You are thinking about 'no service password-recovery'. I copied the
>procedure from a thread here a while back and have it at home. I will post
>it later. I don't think that is what is happening here as the console port
>will function normally it just won't let you break at the beginning. the
>confreg 1202 means that the speed of the console port has been changed. I
>will have to dig into a book at home to get what speed that 1202 sets to.
>It
>is out on cco also.
>
>
>>From: P729 <p729@cox.net>
>>Reply-To: P729 <p729@cox.net>
>>To: "Casey, Paul (6822)" <Paul.Casey@o2.com>, "'CCIE-Groupstudy'"
>><ccielab@groupstudy.com>
>>Subject: Re: Please re- read a see can you help (More exact problem)
>>Date: Fri, 21 Jun 2002 11:43:13 -0700
>>
>>Too bad the archive search is still broken. I seem to recall a service of
>>some type that made it harder to break into the 26/3600 series routers.
>>Although the name of the service made it sound like it would be impossible
>>to break into rommon, someone wrote in that there is actually a small
>>window
>>of opportunity to break in and set the config register with no echo and
>>then
>>reboot. My CCO searches are coming up empty, so it may have been in an
>>special ISP train.
>>
>>Can you post the output of 'show ver' ?
>>
>>Regards,
>>
>>Mas Kato
>>https://ecardfile.com/id/mkato
>>----- Original Message -----
>>From: "Casey, Paul (6822)" <Paul.Casey@o2.com>
>>To: "'CCIE-Groupstudy'" <ccielab@groupstudy.com>
>>Cc: "'Hyunseog Ryu'" <moonhunt@firewall.moonworld.org>; "'Bauer, Rick'"
>><BAUERR@toysrus.com>
>>Sent: Friday, June 21, 2002 10:25 AM
>>Subject: Please re- read a see can you help (More exact problem)
>>
>>
>> > Password recovery page doesnt doesnt help
>> >
>> > You dont see anything with console access in Hyperterminal...
>> >
>> > Here my serious problem
>> >
>> > I have a router and I dont know the enable password for it, 12-14
>>months
>>old
>> > and no one can remember the password.
>> > Thats not the worst
>> > I can get into user mode and when I type show version the confreg
>>register
>> > is set to 0x1202 ... (seemed a bit funny)
>> >
>> > Now when the router boots and I connect to the console port you cant
>>see
>> > anything happening on the console port, therefore I cant get into
>>romon
>> > mode Pressing keys has not effect, You just cant see anything or do
>> > anything
>> >
>> > This confreg-reg setting must have done something serious.
>> >
>> > However, after several minutes when I connect to the aux port I get
>>"press
>> > any key to continue" appears on hyper
>> > terminal screen and I am back in user mode again.
>> > Aux mode only becomes active after bootup,
>> >
>> > image is still booting so thats ok, but back in user access, without
>> > password.
>> > and cant get to console because of the confreg-reg setting ..... and
>>cant
>> > change confreg-reg from user mode..
>> >
>> >
>> > I need to get access to this router ASAP and get access to romon fix
>>the
>> > password problem.
>> >
>> > it is a 2600 series router .....
>> > Also when I check the interfaces for user mode, they are all
>> > administratively shut down... so thats no help...
>> >
>> > I seemed to be locked out of the router, except for user mode which
>>seems
>>to
>> > be good for nothing.
>> > A bit of a catch 22 situation.
>> >
>> >
>> > Any help appreciated.,..
>> >
>> >
>> >
>>****************************************************************************
>>************
>> >
>> > This E-mail is from O2. The E-mail and any files
>> > transmitted with it are confidential and may also be privileged and
>>intended
>> > solely for the use of the individual or entity to whom they are
>>addressed.
>> > Any unauthorised direct or indirect dissemination, distribution or
>>copying
>> > of this message and any attachments is strictly prohibited. If you have
>> > received the E-mail in error please notify postmaster@O2.com or
>> > telephone ++ 353 1 6095000.
>> >
>> >
>>****************************************************************************
>>*************
This archive was generated by hypermail 2.1.4 : Tue Jul 02 2002 - 08:12:39 GMT-3