From: carl.newman@xxxxxxxxxxxxx
Date: Fri Jun 21 2002 - 16:13:14 GMT-3
Just an Idea,
You may have to change the default speed of the HyperTerminal to some thing
other than 9600. I remember the register changing with the default console
port change baud rate if you change it in confreg. A register guide is in
the front of the Solie book. I would pick a few speeds and test.
Carl
-----Original Message-----
From: P729 [mailto:p729@cox.net]
Sent: Friday, June 21, 2002 1:43 PM
To: Casey, Paul (6822); 'CCIE-Groupstudy'
Subject: Re: Please re- read a see can you help (More exact problem)
Too bad the archive search is still broken. I seem to recall a service of
some type that made it harder to break into the 26/3600 series routers.
Although the name of the service made it sound like it would be impossible
to break into rommon, someone wrote in that there is actually a small window
of opportunity to break in and set the config register with no echo and then
reboot. My CCO searches are coming up empty, so it may have been in an
special ISP train.
Can you post the output of 'show ver' ?
Regards,
Mas Kato
https://ecardfile.com/id/mkato
----- Original Message -----
From: "Casey, Paul (6822)" <Paul.Casey@o2.com>
To: "'CCIE-Groupstudy'" <ccielab@groupstudy.com>
Cc: "'Hyunseog Ryu'" <moonhunt@firewall.moonworld.org>; "'Bauer, Rick'"
<BAUERR@toysrus.com>
Sent: Friday, June 21, 2002 10:25 AM
Subject: Please re- read a see can you help (More exact problem)
> Password recovery page doesnt doesnt help
>
> You dont see anything with console access in Hyperterminal...
>
> Here my serious problem
>
> I have a router and I dont know the enable password for it, 12-14 months
old
> and no one can remember the password.
> Thats not the worst
> I can get into user mode and when I type show version the confreg register
> is set to 0x1202 ... (seemed a bit funny)
>
> Now when the router boots and I connect to the console port you cant see
> anything happening on the console port, therefore I cant get into romon
> mode Pressing keys has not effect, You just cant see anything or do
> anything
>
> This confreg-reg setting must have done something serious.
>
> However, after several minutes when I connect to the aux port I get
"press
> any key to continue" appears on hyper
> terminal screen and I am back in user mode again.
> Aux mode only becomes active after bootup,
>
> image is still booting so thats ok, but back in user access, without
> password.
> and cant get to console because of the confreg-reg setting ..... and cant
> change confreg-reg from user mode..
>
>
> I need to get access to this router ASAP and get access to romon fix the
> password problem.
>
> it is a 2600 series router .....
> Also when I check the interfaces for user mode, they are all
> administratively shut down... so thats no help...
>
> I seemed to be locked out of the router, except for user mode which seems
to
> be good for nothing.
> A bit of a catch 22 situation.
>
>
> Any help appreciated.,..
>
>
>
****************************************************************************
************
>
> This E-mail is from O2. The E-mail and any files
> transmitted with it are confidential and may also be privileged and
intended
> solely for the use of the individual or entity to whom they are addressed.
> Any unauthorised direct or indirect dissemination, distribution or copying
> of this message and any attachments is strictly prohibited. If you have
> received the E-mail in error please notify postmaster@O2.com or
> telephone ++ 353 1 6095000.
>
>
****************************************************************************
*************
This archive was generated by hypermail 2.1.4 : Tue Jul 02 2002 - 08:12:39 GMT-3