From: Lance (Lance@xxxxxxxxxxxxx)
Date: Wed Jun 19 2002 - 00:29:17 GMT-3
Thanks to all that helped. It ended up being a issue with the router.
Running an older version of the IOS (11.2.11). When I swapped the router
out the problem corrected itself. Thanks for everyones help.
Lance
----- Original Message -----
From: "George Spahl" <g.spahl@insightbb.com>
To: "'Lance'" <Lance@advnetech.com>; <ccielab@groupstudy.com>
Sent: Tuesday, June 18, 2002 7:29 AM
Subject: RE: OSPF Demand Circuit issues
> Lance,
> Here's a link into the archives to an old post that might help you get
> started. The only thing is where I mentioned "debug ip packet detail" I
> could better have said "debug dialer packets". Hope this helps!
> George
> www.groupstudy.com/archives/ccielab/200203/msg00354.html
>
>
> -----Original Message-----
> From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
> Lance
> Sent: Monday, June 17, 2002 11:15 PM
> To: ccielab@groupstudy.com
> Subject: OSPF Demand Circuit issues
>
> My demand circuit is bouncing up and down.
> R5 is connecting to R3 via ISDN. Both routers have the command no
> peer-neighbor routes entered as well as both having the ip ospf
> damand-circut
> command. I dont understand why it is not working. Anyone have any
> ideas?
> Also what command do I use to show if all my routers understand the DNA
> bit?
> Also R5 never shows R3 as a neighbor when the ISDN line is up. R3 shows
> R5 as
> a neighbor in the INIT state, never full ?
>
> Any guru's out there want to tackle this one? BTW the search
> functionality on
> the site is down.
>
>
>
>
> R5#show dialer
>
> BRI0/0 - dialer type = ISDN
>
> Dial String Successes Failures Last called Last status
> 770794XXXX 5 4 00:00:05 successful
> 0 incoming call(s) have been screened.
> 0 incoming call(s) rejected for callback.
>
> BRI0/0:1 - dialer type = ISDN
> Idle timer (120 secs), Fast idle timer (20 secs)
> Wait for carrier (30 secs), Re-enable (15 secs)
> Dialer state is data link layer up
> Dial reason: ip (s=133.6.65.5, d=224.0.0.5)
> Time until disconnect 115 secs
> Connected to 770794xxxx (r3)
>
> R5 is connecting to R3 via ISDN. Both routers have the command no
> peer-neighbor routes entered as well as both having the ip ospf
> damand-circut
> command. I dont understand why it is not working. Anyone have any
> ideas?
> Also what command do I use to show if all my routers understand the DNA
> bit?
>
>
>
> R5#
> 00:08:00: %ISDN-6-DISCONNECT: Interface BRI0/0:1 disconnected from
> 770794xxxx
> r3, call lasted 120 seconds
> 00:08:00: %LINK-3-UPDOWN: Interface BRI0/0:1, changed state to down
> R5#
> 00:08:00: %LINEPROTO-5-UPDOWN: Line protocol on Interface BRI0/0:1,
> changed
> state to down
> R5#
> 00:08:10: %LINK-3-UPDOWN: Interface BRI0/0:1, changed state to up
> R5#
> 00:08:10: %LINEPROTO-5-UPDOWN: Line protocol on Interface BRI0/0:1,
> changed
> state to up
> R5#
> 00:08:16: %ISDN-6-CONNECT: Interface BRI0/0:1 is now connected to
> 770794xxxx
> r3
> R5#
This archive was generated by hypermail 2.1.4 : Tue Jul 02 2002 - 08:12:37 GMT-3