From: David Luu (wicked01@xxxxxxxxxxxxx)
Date: Sat May 18 2002 - 20:27:23 GMT-3
on R6, i believe you did not paste the whole config...you are missing the
dial peers and ospf routing
on R11, i notice that dial peers 2 and 3 are exactly the same, might want
to get rid of 1
At 05:27 PM 5/18/2002 -0500, cash2001 wrote:
>I am stuck on a voice lab scenario from the Satterlee book. The traffic
>is traversing an ATM link. Please excuse any ignorance as this is my
>first post and in the book, there is no way to test the connectivity.
>Also, what would/should a successful 'csim' output look like?
>
> --------( R6 ) ------- --( R9 )------ -- ( R11 ) -----
>FXS ---- ATM3/0 ----- ATM0 --- S1--- S0/0 ---- FXS
>
>Output from csim start:
>
>r6#csim start 3333
>csim: called number = 3333, loop count = 1 ping count = 0
>
>csim: loop = 1, failed = 1
>csim: call attempted = 1, setup failed = 1, tone failed = 0
>
>Configs (R6):
>
>version 12.1
>no service single-slot-reload-enable
>service timestamps debug uptime
>service timestamps log uptime
>no service password-encryption
>!
>hostname r6
>!
>logging rate-limit console 10 except errors
>!
>memory-size iomem 10
>ip subnet-zero
>!
>no ip finger
>no ip domain-lookup
>!
>ip audit notify log
>ip audit po max-events 100
>!
>call rsvp-sync
>cns event-service server
>!
>interface Loopback0
> ip address 135.25.2.1 255.255.255.255
>!
>interface BRI0/0
> no ip address
> shutdown
>!
>interface Ethernet0/0
> no ip address
> shutdown
> half-duplex
>!
>interface Serial0/0
> ip address 192.1.1.3 255.255.255.0
> encapsulation frame-relay
> no fair-queue
> frame-relay lmi-type ansi
>!
>interface TokenRing0/0
> no ip address
> shutdown
> ring-speed 16
>!
>interface FastEthernet1/0
> no ip address
> shutdown
> duplex auto
> speed auto
>
>Configs (R11):
>
>version 12.1
>service timestamps debug uptime
>service timestamps log uptime
>no service password-encryption
>!
>hostname r11
>!
>memory-size iomem 10
>ip subnet-zero
>!
>ip audit notify log
>ip audit po max-events 100
>!
>voice-port 1/0/0
>!
>voice-port 1/0/1
>!
>dial-peer voice 1 pots
> destination-pattern 3333
> port 1/0/0
>!
>dial-peer voice 2 voip
> destination-pattern 2222
> session target ipv4:135.25.2.1
>!
>dial-peer voice 3 voip
> destination-pattern 2222
> session target ipv4:135.25.2.1
>!
>interface Loopback0
> ip address 135.25.3.1 255.255.255.255
>!
>interface FastEthernet0/0
> no ip address
> shutdown
> duplex auto
> speed auto
>!
>interface Serial0/0
> ip address 195.1.2.2 255.255.255.252
> no fair-queue
>!
>interface Serial0/1
> no ip address
> shutdown
>!
>router ospf 64
> log-adjacency-changes
> network 135.25.0.0 0.0.255.255 area 0
> network 195.1.0.0 0.0.255.255 area 0
>!
>ip classless
>ip http server
>!
>line con 0
>line aux 0
>line vty 0 4
>!
>no scheduler allocate
>end
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 10:59:00 GMT-3