From: George Spahl (g.spahl@xxxxxxxxxxxxx)
Date: Tue Apr 30 2002 - 15:44:44 GMT-3
It seems to work fine over a tunnel for me as well. The only thing is
that once again I have to set up IPX addressing on the interfaces and
include it in the EIGRP so that the adjacency forms. Once the adjacency
comes up I can swap the IPX addressing for IPXWAN (either using an IPX
address or unnumbered) and it's fine with it from then on. The routes
being exchanged are EIGRP, however the IPXWAN debug shows that it forms
the IPXWAN link with RIP (it would prefer NLSP, but I didn't have it
configured). HTH.
George
-----Original Message-----
From: Chua, Parry [mailto:Parry.Chua@compaq.com]
Sent: Tuesday, April 30, 2002 5:57 AM
To: George Spahl; Erhan Kurt; Curtis Phillips; ccielab@groupstudy.com
Subject: RE: IPXWAN unnumbered and EIGRP
I just try it on ipx eigrp , it work on HDLC and PPP, either number or
unnumber.
For unnumber, I take the internal network number, ie no netw in rip and
netw in eigrp.
shu/no shu with debug to ensure that ipxeigrp event on the serial
link....
> Parry Chua
>
>
-----Original Message-----
From: George Spahl [mailto:g.spahl@insightbb.com]
Sent: Sunday, April 28, 2002 4:52 AM
To: 'Erhan Kurt'; 'Curtis Phillips'; ccielab@groupstudy.com
Subject: RE: IPXWAN unnumbered and EIGRP
Curtis,
I'm also unable to make IPXWAN work with IPX EIGRP. I've tried it with
IPX EIGRP configured on both sides of a point-to-point (HDLC) link and
IPX RIP turned off on both sides. I've also tried numbered and
unnumbered on the IPXWAN.
Whenever I bring up the link and watch the debug it looks like IPXWAN
negotiates RIP for the link and then when I look at the routers I see
that there have been RIP routes exchanged across the link. This even
though I had issued a "no ipx router rip" prior to bringing up the
IPXWAN link. I previously thought that IPXWAN supported EIGRP, but I
guess that isn't the case. It seems that IPXWAN supports only NLSP and
IPX RIP (in that order of preference)and not EIGRP. Has anyone seen
this work differently?
George
-----Original Message-----
From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
Erhan Kurt
Sent: Friday, April 26, 2002 9:34 AM
To: Curtis Phillips; ccielab@groupstudy.com
Subject: RE: IPXWAN unnumbered and EIGRP
Use network internal network in EIGRP
No net in RIP
Erhan
-----Original Message-----
From: Curtis Phillips [mailto:cphillips@blazenet.net]
Sent: 26 Nisan 2002 Cuma 15:48
To: ccielab@groupstudy.com
Subject: IPXWAN unnumbered and EIGRP
Hello All,
Is nay one aware of how to configure IPX EIGRP over an unnumbered
interface
with IPXWAN enabled.
It appears that RIP successfully is negotiated by default(When isn't
it:-) )
But I am having difficulty getting RIP shut down over the link and EIGRP
working.
How is rip disabled without network number?
How is EIGRP enabled without network number?
Thanks in advance,
Curtis
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 10:58:24 GMT-3