From: Bob Sinclair (bsin@xxxxxxxxx)
Date: Sun Apr 21 2002 - 21:01:06 GMT-3
Guy,
A reasonable question, I should have documented. The statement below stuck in
my head (I tend to equate SRB and Token Ring, so maybe too broad).
"Integrated routing and bridging is supported for transparent bridging, but not
for source-route bridging (SRB)."
Taken from this link on the DOC CD:
http://127.0.0.1:8080/cc/td/doc/product/software/ios121/121cgcr/ibm_c/bcprt1/bc
dtb.htm#xtocid186944
I suppose it may work with SRT on the Token Ring, so perhaps my statement was a
bit broad.
-Bob
----- Original Message -----
From: "Lupi, Guy" <Guy.Lupi@eurekaggn.com>
To: "'Bob Sinclair'" <bsin@erols.com>
Cc: <ccielab@groupstudy.com>
Sent: Sunday, April 21, 2002 7:43 PM
Subject: RE: IRB with OSPF/EIGRP
> Really!?!? That is strange, with the exception of the OSPF/EIGRP thing, it
> is working just as I would expect it to work. Where did you see that it
> wasn't supported? Not that I don't believe you, I just want to take a look,
> because it seems to be working.
>
> ~-----Original Message-----
> ~From: Bob Sinclair [mailto:bsin@erols.com]
> ~Sent: Sunday, April 21, 2002 6:58 PM
> ~To: Lupi, Guy
> ~Cc: ccielab@groupstudy.com
> ~Subject: Re: IRB with OSPF/EIGRP
> ~
> ~
> ~Guy,
> ~
> ~If I understand you correctly, you want to do IRB with Token
> ~Ring interfaces. This is not supported.
> ~
> ~-Bob
> ~
> ~----- Original Message -----
> ~From: "Lupi, Guy" <Guy.Lupi@eurekaggn.com>
> ~To: "Lupi, Guy" <Guy.Lupi@eurekaggn.com>; <ccielab@groupstudy.com>
> ~Sent: Sunday, April 21, 2002 3:44 PM
> ~Subject: RE: IRB with OSPF/EIGRP
> ~
> ~
> ~> Ok, I have it working now with IRB, but it is on Ethernet.
> ~Same setup as
> ~> below, but the routers below I described before are token
> ~ring. So I have
> ~> it working with IRB using all Ethernet, but it doesn't seem
> ~to work with IRB
> ~> when it is all token ring. Any ideas?
> ~>
> ~> ~-----Original Message-----
> ~> ~From: Lupi, Guy
> ~> ~Sent: Sunday, April 21, 2002 3:05 PM
> ~> ~To: 'ccielab@groupstudy.com'
> ~> ~Subject: IRB with OSPF/EIGRP
> ~> ~
> ~> ~
> ~> ~I have a setup like below, and I was trying to run OSPF or
> ~> ~EIGRP between the
> ~> ~two routers that are in the bridge group and the BVI router,
> ~> ~but I couldn't
> ~> ~get it to work until I used tunnels. Has anyone gotten
> ~OSPF or EIGRP
> ~> ~working with IRB without using tunnels? Thanks.
> ~> ~
> ~> ~
> ~> ~
> ~> ~ r6
> ~> ~ BVI
> ~> ~ / \
> ~> ~ / \
> ~> ~ r3 r4
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 10:58:15 GMT-3