From: Brian Lodwick (xpranax@xxxxxxxxxxx)
Date: Wed Mar 20 2002 - 16:29:43 GMT-3
I've added my comments after your questions ***.
1. Will the config below work in discovering the VPI/VCI, if not what
wil work.
*** try this:
R1:
conf t
interface ATM4/0
ip address 10.10.10.1 255.255.255.0
pvc 0/16 ilmi
exit
atm ilmi-pvc-discovery
end
show atm vc
2. Do I need the "atm pvc 1 0 5 qsaal"?
*** No, qsaal is used for SVC's
3. Do I need to always set the "atm ilmi-keepalive". I don't
discover the prefix for the nsap address if I don't enable
the keep-alive. What value should it be set to?
*** I've never changed the ilmi-keepalive timer from it's default.
*** You are talking about PVC auto-discovery and nsap addresses in the same
sentence?. NSAP addresses are used for SVC's and VCI/VPI pairs are used for
PVC's.
4. What is the show command to see the discovered VPI/VCI? Is it
"show atm ilmi-status"?
*** show atm vc
>>>Brian
>From: "Frank B" <frank@buff-net.com>
>Reply-To: "Frank B" <frank@buff-net.com>
>To: "'Emmanuel Oppong'" <e-oppong@attbi.com>, <ccielab@groupstudy.com>
>Subject: RE: VPI/VCI Autodiscovery Procedure - HELP!
>Date: Wed, 20 Mar 2002 08:28:18 -1000
>
>Except for the manual ilmi keepalive configuration this is the basic
>config for both ends. If there's a PVC configured both ends should pick
>it up. Assuming the routers are connected to the ports specified in the
>PVC configuration on the switch ;-)
>
>If the switch is a LS1010 this will do it. If not, I'm not much help.
>Good luck. Frank
>
>
>-----Original Message-----
>From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
>Emmanuel Oppong
>Sent: Wednesday, March 20, 2002 7:52 AM
>To: ccielab@groupstudy.com
>Subject: VPI/VCI Autodiscovery Procedure - HELP!
>
>Guys/Gals,
>
>I am not sure if the ATM switch I am using is capable of VPI/VCI
>autodiscovery. I tried the config below and it never worked. If
>you have done this before, I will highly appreciate your response
>to these questions. My test is a couple of days away!
>
>Thanks !!!
>
>1. Will the config below work in discovering the VPI/VCI, if not what
>wil work.
>2. Do I need the "atm pvc 1 0 5 qsaal"?
>3. Do I need to always set the "atm ilmi-keepalive". I don't
>discover the prefix for the nsap address if I don't enable
>the keep-alive. What value should it be set to?
>4. What is the show command to see the discovered VPI/VCI? Is it
>"show atm ilmi-status"?
>
>R1:
>conf t
>interface ATM4/0
> ip address 10.10.10.1 255.255.255.0
> atm ilmi-keepalive 10
> pvc 0/16 ilmi
> atm ilmi-pvc-discovery
>!
>exit
>#show atm ilmi-status
>
>
>R2:
>conf t
>interface ATM4/0
> ip address 10.10.10.2 255.255.255.0
> atm ilmi-keepalive 10
> pvc 0/16 ilmi
> atm ilmi-pvc-discovery
>!
>exit
>#show atm ilmi-status
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 10:57:14 GMT-3