From: Gregg Malcolm (greggm@xxxxxxxxxxxxx)
Date: Tue Mar 12 2002 - 17:16:25 GMT-3
Joe,
Can you give us the loop ip addresses on the wonderfull AS5300 as well ?
----- Original Message -----
From: "Joe Freeman" <joe.freeman@centurytel.com>
To: "Ccielab" <ccielab@groupstudy.com>
Sent: Tuesday, March 12, 2002 10:18 AM
Subject: Eigrp over DDR using Dial Profiles?
> Greetings-
>
> I think I'm probably just being dense at the moment, but I cannot get
EIGRP
> to work via a dial backup line between a 2600 and a 5350.
>
> I can get PPP up with no problems. I can pass traffic using the default
> static route in the 2600 pointing to the Dialer1 interface. I just can't
> seem to get EIGRP to work. I'm obviously missing something, but I'll be
> danged if I can see it at the moment.
>
> This will ultimately be a backup interface for a frame-relay connection on
> another interface.
>
> Also, I should mention that this is IOS 12.2(8)T, Telco Plus. I know it's
> bleeding edge, but 12.2(8)T is the only IOS that supports BOTH the
> VWIC-MFT-T1 and the WIC1-AM. Telco Plus is the required feature set, as
> there is no Enterprise Plus in 12.2(8)T.
>
> Thanks-
> Joe Freeman, CCNP-VA/CCDP
>
> Here's important part of the 2600's config:
>
> interface Loopback0
> ip address 10.130.254.1 255.255.255.255
> !
> interface FastEthernet0/0
> ip address 10.0.209.249 255.255.252.0
> speed 10
> full-duplex
> !
> interface Async1
> no ip address
> encapsulation ppp
> no ip mroute-cache
> dialer in-band
> dialer pool-member 1
> dialer-group 1
> autodetect encapsulation ppp
> async default routing
> async mode interactive
> no peer default ip address
> no fair-queue
> no ppp microcode
> !
> interface Dialer1
> ip unnumbered Loopback0
> encapsulation ppp
> dialer pool 1
> dialer idle-timeout 300
> dialer string 8070655
> dialer hold-queue 50
> dialer-group 1
> no peer default ip address
> ppp authentication pap callin
> ppp pap sent-username <deleted> password 7 <deleted>
> !
> router eigrp 1
> network 10.0.0.0
> no auto-summary
> no eigrp log-neighbor-changes
> !
> no ip http server
> ip classless
> ip route 0.0.0.0 0.0.0.0 Dialer1 250
> ip pim bidir-enable
> !
> !
> !
> dialer-list 1 protocol ip permit
>
> Here's the config from the AS5350:
> !
> interface Serial3/0:23
> description Test PRI
> no ip address
> encapsulation ppp
> ip mroute-cache
> no logging event link-status
> dialer rotary-group 1
> no snmp trap link-status
> isdn switch-type primary-ni
> isdn incoming-voice modem
> isdn T306 30000
> isdn T310 10000
> no cdp enable
> !
> interface Async1
> no ip address
> !
> interface Group-Async1
> ip unnumbered Loopback1
> encapsulation ppp
> no ip route-cache
> ip tcp header-compression passive
> no ip mroute-cache
> no logging event link-status
> autodetect encapsulation ppp
> async default routing
> async dynamic routing
> async mode interactive
> ipx ppp-client Loopback0
> ipx update interval sap changes-only
> no snmp trap link-status
> peer default ip address pool analog
> compress stac
> ppp authentication pap
> group-range 1/00 1/107
> hold-queue 75 in
> !
> interface Dialer1
> ip unnumbered Loopback0
> encapsulation ppp
> no ip route-cache
> no ip mroute-cache
> no logging event link-status
> dialer in-band
> dialer idle-timeout 0
> dialer load-threshold 1 outbound
> dialer-group 1
> ipx network ACCE99C
> no snmp trap link-status
> peer default ip address pool dialup-isdn
> compress stac
> no cdp enable
> ppp authentication chap pap
> ppp multilink
> !
> router eigrp 1
> network 10.0.0.0
> default-metric 10000 100 255 1 1500
> no auto-summary
> eigrp log-neighbor-changes
> !
> ip local pool Analog 10.0.31.1 10.0.31.254
> ip local pool analog 10.0.249.1 10.0.249.254
> ip local pool dialup-isdn 10.0.250.1 10.0.250.254
> ip classless
> ip flow-export destination 10.0.21.5 9996
> ip flow-aggregation cache as
> cache entries 2046
> cache timeout inactive 200
> cache timeout active 45
> export destination 10.0.21.5 9996
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 10:57:02 GMT-3