From: Brian Lodwick (xpranax@xxxxxxxxxxx)
Date: Fri Mar 08 2002 - 14:04:08 GMT-3
FYI...
Just wanted to point out that the command:
atm pvc _/_
in conjunction with a map-list is the old version of ATM mapping, and the
new version of this command:
pvc _/_
is recommended.
>>>Brian
>From: "Lupi, Guy" <Guy.Lupi@eurekaggn.com>
>Reply-To: "Lupi, Guy" <Guy.Lupi@eurekaggn.com>
>To: "'Paul Lalonde'" <plalonde2@cogeco.ca>, ccielab@groupstudy.com
>Subject: RE: ATM Interface Setup
>Date: Fri, 8 Mar 2002 11:24:41 -0500
>
>Thanks to all who responded, they gave me the wrong pvc vpi and vci values.
>They told me to use 0/32 and 0/32, when in acutality it is 0/100 and 0/101.
>It is working now, thanks.
>
>~-----Original Message-----
>~From: Paul Lalonde [mailto:plalonde2@cogeco.ca]
>~Sent: Friday, March 08, 2002 11:41 AM
>~To: Lupi, Guy; ccielab@groupstudy.com
>~Subject: Re: ATM Interface Setup
>~
>~
>~Hi Guy,
>~
>~How about turning on PVC auto discovery? That way, you should
>~be able to
>~detect the PVCs configured on the ATM switch.
>~
>~I think its atm ilmi-autodiscovery under the physical interface.
>~
>~Hope this helps!
>~Paul
>~
>~----- Original Message -----
>~From: "Lupi, Guy" <Guy.Lupi@eurekaggn.com>
>~To: "'Paul Lalonde'" <plalonde2@cogeco.ca>; <ccielab@groupstudy.com>
>~Sent: Friday, March 08, 2002 11:00 AM
>~Subject: RE: ATM Interface Setup
>~
>~
>~> I don't have access to the LS1010, so there is no way for me
>~to verify the
>~> setup unfortunately. It is on the IPExpert virtual rack.
>~>
>~> ~-----Original Message-----
>~> ~From: Paul Lalonde [mailto:plalonde2@cogeco.ca]
>~> ~Sent: Friday, March 08, 2002 11:16 AM
>~> ~To: Lupi, Guy; ccielab@groupstudy.com
>~> ~Subject: Re: ATM Interface Setup
>~> ~
>~> ~
>~> ~Hi Guy,
>~> ~
>~> ~Can you forward us the PVC list on the ATM switch? Make sure
>~> ~that the PVCs
>~> ~that you've defined on the routers (0/32) is the same on the
>~> ~ATM switch.
>~> ~
>~> ~Try a 'show atm pvc' or 'show atm map' on the LS1010. Also,
>~check out:
>~> ~
>~> ~http://www.cisco.com/warp/public/121/ipoveratm.html
>~> ~
>~> ~and
>~> ~
>~> ~http://www.cisco.com/warp/public/121/index.shtm
>~> ~
>~> ~Hope this helps!
>~> ~
>~> ~Paul
>~> ~
>~> ~----- Original Message -----
>~> ~From: "Lupi, Guy" <Guy.Lupi@eurekaggn.com>
>~> ~To: <ccielab@groupstudy.com>
>~> ~Sent: Friday, March 08, 2002 10:20 AM
>~> ~Subject: ATM Interface Setup
>~> ~
>~> ~
>~> ~> I have some virtual rack time today, and it is my first time
>~> ~setting up
>~> ~ATM.
>~> ~> I am following a book that I have to set it up, I can't get
>~> ~it to work,
>~> ~the
>~> ~> interfaces are up but I can't ping the other side. There
>~> ~are 2 routers
>~> ~> connected to an LS1010 ATM switch, I included the configs
>~> ~below, I would
>~> ~> appreciate it if someone could tell me whether or not the
>~configs are
>~> ~> correct. The pvc for each router is 1, vpi 0 vci 32, thanks.
>~> ~>
>~> ~> hostname r9
>~> ~> !
>~> ~> !
>~> ~> !
>~> ~> !
>~> ~> !
>~> ~> !
>~> ~> ip subnet-zero
>~> ~> no ip finger
>~> ~> !
>~> ~> !
>~> ~> !
>~> ~> !
>~> ~> !
>~> ~> !
>~> ~> !
>~> ~> !
>~> ~> interface ATM0/0
>~> ~> no ip address
>~> ~> no atm ilmi-keepalive
>~> ~> !
>~> ~> interface ATM0/0.1 multipoint
>~> ~> ip address 6.9.6.9 255.255.255.0
>~> ~> map-group tor6
>~> ~> atm pvc 1 0 32 aal5snap
>~> ~> !
>~> ~> interface Ethernet1/0
>~> ~> no ip address
>~> ~> shutdown
>~> ~> !
>~> ~> interface Ethernet1/1
>~> ~> no ip address
>~> ~> shutdown
>~> ~> !
>~> ~> !
>~> ~> ip classless
>~> ~> ip http server
>~> ~> !
>~> ~> !
>~> ~> map-list tor6
>~> ~> ip 6.9.6.6 atm-vc 1 broadcast
>~> ~> !
>~> ~> !
>~> ~> !
>~> ~> !
>~> ~> !
>~> ~> !
>~> ~> !
>~> ~> !
>~> ~> !
>~> ~> !
>~> ~> !
>~> ~> line con 0
>~> ~> logging synchronous
>~> ~> transport input none
>~> ~> line aux 0
>~> ~> line vty 0 4
>~> ~> !
>~> ~> end
>~> ~>
>~> ~> r9#
>~> ~>
>~> ~>
>~> ~>
>~> ~> hostname r6
>~> ~> !
>~> ~> !
>~> ~> !
>~> ~> !
>~> ~> !
>~> ~> !
>~> ~> ip subnet-zero
>~> ~> no ip finger
>~> ~> !
>~> ~> !
>~> ~> !
>~> ~> !
>~> ~> !
>~> ~> !
>~> ~> !
>~> ~> !
>~> ~> interface ATM0/0
>~> ~> no ip address
>~> ~> no atm ilmi-keepalive
>~> ~> !
>~> ~> interface ATM0/0.1 multipoint
>~> ~> ip address 6.9.6.6 255.255.255.0
>~> ~> map-group tor9
>~> ~> atm pvc 1 0 32 aal5snap
>~> ~> !
>~> ~> interface Ethernet1/0
>~> ~> no ip address
>~> ~> shutdown
>~> ~> !
>~> ~> interface Serial1/0
>~> ~> no ip address
>~> ~> shutdown
>~> ~> !
>~> ~> !
>~> ~> ip classless
>~> ~> ip http server
>~> ~> !
>~> ~> !
>~> ~> map-list tor9
>~> ~> ip 6.9.6.9 atm-vc 1 broadcast
>~> ~> !
>~> ~> !
>~> ~> !
>~> ~> !
>~> ~> !
>~> ~> !
>~> ~> !
>~> ~> !
>~> ~> !
>~> ~> !
>~> ~> !
>~> ~> line con 0
>~> ~> logging synchronous
>~> ~> transport input none
>~> ~> line aux 0
>~> ~> line vty 0 4
>~> ~> !
>~> ~> end
>~> ~>
>~> ~> r6#
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 10:56:57 GMT-3