From: MADMAN (dmadlan@xxxxxxxxx)
Date: Wed Mar 06 2002 - 14:21:25 GMT-3
I found out that indeed MARINA is the code name for the L3 card. Like
I mentioned earlier, I got a 6500 SUPII card that came up with a DRACO
prompt, code name for the SUPII card and Cisco said that they had
inadvertantly shipped out 10 SUPs that still had a diagnostic image on
it. Call TAC and get it RMA'd is my guess.
Dave
David wrote:
>
> Sorry to bring this topic up again, but need help
> despartely
>
> ------------------------------------------------------------------------
>
> I'm having issues setting up Cat 4K with L3
> module. This are the modules:
> Switching Supervisor - WS-X4012
> Router Switch Card - WS-X4232-L3
>
> L3 module did not seem to have IOS so I ran
> Xmodem to put cat4232-in-mz.120-18.W5.22a.bin
> IOS file
> on. That seem to go OK but when resstarted the
> box, I
> got the output below. Any ideas what's going on
> i.e.
> why no CLI is present??
>
> BOOTUP:
>
> Compiled Fri 09-Jun-00 10:17 by wkassa
> Diagnostic Software (MARINA-DIAG), Version
> 1.4(1)
> [wkassa j_conn]
>
> Copyright (c) Cisco Systems Inc. 1998-1999
>
> MARINA1%
> ROMMON: Entered init
> ROMMON: Cold Reset frame @0x00000000
> ROMMON: Reading reset reason register
> ROMMON: Valid NVRAM config
>
> System Bootstrap, Version 12.0(7)W5(15b)
> RELEASE
> SOFTWARE
> Copyright (c) 2000 by cisco Systems, Inc.
>
> ROMMON: Initializing exceptions
> ROMMON: Initializing TLB
> ROMMON: Initializing cache
> ROMMON: Sizing and zeroing main memory ... 64
> MBytes
> ROMMON: Sizing non-volatile memory ... 128
> KBytes
> ROMMON: Exiting init
>
> Catalyst-4232 platform with 65536 Kbytes of
> main
> memory
>
> Initialize MMC diag test driver
> Marina system recognized.
> NP54 0, XPIF Ver.1 Port 0 at 1244 M
> NP54 0, XPIF Ver.1 Port 1 at 1244 M
> NP54 2, XPIF Ver.1 Port 0 at 1244 M
> NP54 2, XPIF Ver.1 Port 1 at 1244 M
> ****** Spawn status register polling task
> ******
> fpga_ucode begin from 0x8019fe28
> FPGA_DNLD completed
> Thermostat #0: config reg reads 0x0a
> Thermostat #1: config reg reads 0xff
>
> Booting on Dec 31 1999 23:59:59
>
> Compiled Fri 09-Jun-00 10:17 by wkassa
> Diagnostic Software (MARINA-DIAG), Version
> 1.4(1)
> [wkassa j_conn]
>
> Copyright (c) Cisco Systems Inc. 1998-1999
>
> MARINA1%
> ROMMON: Entered init
> ROMMON: Cold Reset frame @0x00000000
> ROMMON: Reading reset reason register
> ROMMON: Valid NVRAM config
>
> System Bootstrap, Version 12.0(7)W5(15b)
> RELEASE
> SOFTWARE
> Copyright (c) 2000 by cisco Systems, Inc.
>
> ROMMON: Initializing exceptions
> ROMMON: Initializing TLB
> ROMMON: Initializing cache
>
>
> AFTER BOOTING:
>
> MARINA1% ?
> Informational Commands:
> Help - Provide Command Help Information
> History - Provide Command History Information
> Keys - Display Control Keys Usage during
> Diagnostics Session
> Errorinfo - Display Diagnostics Error Code
> information
> Version - Display Diagnostics Version
> information
>
>
> =============================================================================
=
> Test Execution Commands:
> Contents - Provide Diagnostic Test Contents
> Information
> Set - Set Diagnostic Section/Test
> Parameter
> Values or Date/Time/Prompt
> Reset - Reset Diagnostic Section/Test
> Parameters
> to Default Values
> Resetmisc - Misc. Reset PHY/gig ports, XPIF
> Inband,
> Link PLD & nP5400s
> Unresetmisc- Misc. Unreset PHY/gig ports, XPIF
> Inband, Link PLD & nP5400s
> Show - Show Diagnostic Section(s)/Test(s)
> Parameter Values
> Run - Run Diagnostic Section(s)/Test(s)
> Skip - Skip Diagnostic Section(s)/Test(s)
> in
> RUN ALL Command
> Results - Display Diagnostic
> Section(s)/Test(s)
> Execution Results
> Ps - Provide Scheduled Diagnostic Test(s)
> Information
> Kill - Remove Scheduled Diagnostic Test(s)
>
>
> =============================================================================
=
> Debug Commands:
> Write - Write Data in one or more Address
> locations
> Read - Read Data from one or more Address
> locations
> Compare - Compare Data with Contents of one or
> more Address locations
> Search - Search Data in one or more Address
> locations
> Verify - Read & Verify Data from one or more
> Address locations
> Asm - Assemble R5000 instructions in one
> or
> more Memory locations
> Dasm - Disassemble R5000 machine codes from
> one
> or more Memory locations
> Execute - Execute R5000 machine codes from one
> or
> more Memory locations
> Test - Test one Address location performing
> R/W
> Operation
> NP54 - Perform NP5400 Debugging Functions
> EPc - Perform EPIF/XPIF Debugging
> Functions
> GCam - Perform GigFPGA/TCAM Debugging
> Functions
> EPIFSNAKE - 10/100 Ports Smartbits Snake Test
> XPIFSNAKE - Gigabit Ports Smartbits Snake Test
> SYSSNAKE - All Ports Smartbits Snake Test
> Troubleshoot - Use for fault isolation
>
>
> =============================================================================
=
> Miscellaneous Commands:
> Clear - Clear Screen
> Exit - Exit Diagnostic/Debug Session
> PowerMargin- Power Supplies Margin Setting
> FPGADnld - Download latest FPGA image
> DUMPGT - Dump the Galileo registers
> MARINA2%
>
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 10:56:55 GMT-3