From: David (david_knot@xxxxxxxxx)
Date: Wed Mar 06 2002 - 13:11:06 GMT-3
Sorry to bring this topic up again, but need help
despartely
------------------------------------------------------------------------
I'm having issues setting up Cat 4K with L3
module. This are the modules:
Switching Supervisor - WS-X4012
Router Switch Card - WS-X4232-L3
L3 module did not seem to have IOS so I ran
Xmodem to put cat4232-in-mz.120-18.W5.22a.bin
IOS file
on. That seem to go OK but when resstarted the
box, I
got the output below. Any ideas what's going on
i.e.
why no CLI is present??
BOOTUP:
Compiled Fri 09-Jun-00 10:17 by wkassa
Diagnostic Software (MARINA-DIAG), Version
1.4(1)
[wkassa j_conn]
Copyright (c) Cisco Systems Inc. 1998-1999
MARINA1%
ROMMON: Entered init
ROMMON: Cold Reset frame @0x00000000
ROMMON: Reading reset reason register
ROMMON: Valid NVRAM config
System Bootstrap, Version 12.0(7)W5(15b)
RELEASE
SOFTWARE
Copyright (c) 2000 by cisco Systems, Inc.
ROMMON: Initializing exceptions
ROMMON: Initializing TLB
ROMMON: Initializing cache
ROMMON: Sizing and zeroing main memory ... 64
MBytes
ROMMON: Sizing non-volatile memory ... 128
KBytes
ROMMON: Exiting init
Catalyst-4232 platform with 65536 Kbytes of
main
memory
Initialize MMC diag test driver
Marina system recognized.
NP54 0, XPIF Ver.1 Port 0 at 1244 M
NP54 0, XPIF Ver.1 Port 1 at 1244 M
NP54 2, XPIF Ver.1 Port 0 at 1244 M
NP54 2, XPIF Ver.1 Port 1 at 1244 M
****** Spawn status register polling task
******
fpga_ucode begin from 0x8019fe28
FPGA_DNLD completed
Thermostat #0: config reg reads 0x0a
Thermostat #1: config reg reads 0xff
Booting on Dec 31 1999 23:59:59
Compiled Fri 09-Jun-00 10:17 by wkassa
Diagnostic Software (MARINA-DIAG), Version
1.4(1)
[wkassa j_conn]
Copyright (c) Cisco Systems Inc. 1998-1999
MARINA1%
ROMMON: Entered init
ROMMON: Cold Reset frame @0x00000000
ROMMON: Reading reset reason register
ROMMON: Valid NVRAM config
System Bootstrap, Version 12.0(7)W5(15b)
RELEASE
SOFTWARE
Copyright (c) 2000 by cisco Systems, Inc.
ROMMON: Initializing exceptions
ROMMON: Initializing TLB
ROMMON: Initializing cache
AFTER BOOTING:
MARINA1% ?
Informational Commands:
Help - Provide Command Help Information
History - Provide Command History Information
Keys - Display Control Keys Usage during
Diagnostics Session
Errorinfo - Display Diagnostics Error Code
information
Version - Display Diagnostics Version
information
==============================================================================
Test Execution Commands:
Contents - Provide Diagnostic Test Contents
Information
Set - Set Diagnostic Section/Test
Parameter
Values or Date/Time/Prompt
Reset - Reset Diagnostic Section/Test
Parameters
to Default Values
Resetmisc - Misc. Reset PHY/gig ports, XPIF
Inband,
Link PLD & nP5400s
Unresetmisc- Misc. Unreset PHY/gig ports, XPIF
Inband, Link PLD & nP5400s
Show - Show Diagnostic Section(s)/Test(s)
Parameter Values
Run - Run Diagnostic Section(s)/Test(s)
Skip - Skip Diagnostic Section(s)/Test(s)
in
RUN ALL Command
Results - Display Diagnostic
Section(s)/Test(s)
Execution Results
Ps - Provide Scheduled Diagnostic Test(s)
Information
Kill - Remove Scheduled Diagnostic Test(s)
==============================================================================
Debug Commands:
Write - Write Data in one or more Address
locations
Read - Read Data from one or more Address
locations
Compare - Compare Data with Contents of one or
more Address locations
Search - Search Data in one or more Address
locations
Verify - Read & Verify Data from one or more
Address locations
Asm - Assemble R5000 instructions in one
or
more Memory locations
Dasm - Disassemble R5000 machine codes from
one
or more Memory locations
Execute - Execute R5000 machine codes from one
or
more Memory locations
Test - Test one Address location performing
R/W
Operation
NP54 - Perform NP5400 Debugging Functions
EPc - Perform EPIF/XPIF Debugging
Functions
GCam - Perform GigFPGA/TCAM Debugging
Functions
EPIFSNAKE - 10/100 Ports Smartbits Snake Test
XPIFSNAKE - Gigabit Ports Smartbits Snake Test
SYSSNAKE - All Ports Smartbits Snake Test
Troubleshoot - Use for fault isolation
==============================================================================
Miscellaneous Commands:
Clear - Clear Screen
Exit - Exit Diagnostic/Debug Session
PowerMargin- Power Supplies Margin Setting
FPGADnld - Download latest FPGA image
DUMPGT - Dump the Galileo registers
MARINA2%
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 10:56:55 GMT-3