From: MADMAN (dmadlan@xxxxxxxxx)
Date: Tue Mar 05 2002 - 12:07:00 GMT-3
Return Material Authorization I think. Ya use acronyms so much you
forget the actual meaning:-0
Dave
David wrote:
>
> What is RMAed?
>
> I think it is in diagnostics mode since I get this
> output when I do ?
>
> Any other ideas pls?
>
> MARINA>1% ?
> Informational Commands:
> Help - Provide Command Help Information
> History - Provide Command History Information
> Keys - Display Control Keys Usage during
> Diagnostics Session
> Errorinfo - Display Diagnostics Error Code
> information
> Version - Display Diagnostics Version information
> =============================================================================
=
> Test Execution Commands:
> Contents - Provide Diagnostic Test Contents
> Information
> Set - Set Diagnostic Section/Test Parameter
> Values or Date/Time/Prompt
> Reset - Reset Diagnostic Section/Test Parameters
> to Default Values
> Resetmisc - Misc. Reset PHY/gig ports, XPIF Inband,
> Link PLD & nP5400s
> Unresetmisc- Misc. Unreset PHY/gig ports, XPIF
> Inband, Link PLD & nP5400s
> Show - Show Diagnostic Section(s)/Test(s)
> Parameter Values
> Run - Run Diagnostic Section(s)/Test(s)
> Skip - Skip Diagnostic Section(s)/Test(s) in
> RUN ALL Command
> Results - Display Diagnostic Section(s)/Test(s)
> Execution Results
> Ps - Provide Scheduled Diagnostic Test(s)
> Information
> Kill - Remove Scheduled Diagnostic Test(s)
> =============================================================================
=
> Debug Commands:
> Write - Write Data in one or more Address
> locations
> Read - Read Data from one or more Address
> locations
> Compare - Compare Data with Contents of one or
> more Address locations
> Search - Search Data in one or more Address
> locations
> Verify - Read & Verify Data from one or more
> Address locations
> Asm - Assemble R5000 instructions in one or
> more Memory locations
> Dasm - Disassemble R5000 machine codes from one
> or more Memory locations
> Execute - Execute R5000 machine codes from one or
> more Memory locations
> Test - Test one Address location performing R/W
> Operation
> NP54 - Perform NP5400 Debugging Functions
> EPc - Perform EPIF/XPIF Debugging Functions
> GCam - Perform GigFPGA/TCAM Debugging Functions
> EPIFSNAKE - 10/100 Ports Smartbits Snake Test
> XPIFSNAKE - Gigabit Ports Smartbits Snake Test
> SYSSNAKE - All Ports Smartbits Snake Test
> Troubleshoot - Use for fault isolation
> =============================================================================
=
> Miscellaneous Commands:
> Clear - Clear Screen
> Exit - Exit Diagnostic/Debug Session
> PowerMargin- Power Supplies Margin Setting
> FPGADnld - Download latest FPGA image
> DUMPGT - Dump the Galileo registers
> MARINA>2%
>
> --- MADMAN <dmadlan@qwest.com> wrote:
> >
> > Looks like you may have a card that is in
> > diagnostic mode. I had a
> > 6500 sup card that came up with a funky prompt like
> > your seeing, MARINA,
> > and I had to get it RMAed. Any Cisco guys out there
> > recognize MARINA as
> > the L3 card code name???
> >
> > Dave
> >
> > David wrote:
> > >
> > > I'm having issues setting up Cat 4K with L3
> > module.
> > > This are the modules:
> > > Switching Supervisor - WS-X4012
> > > Router Switch Card - WS-X4232-L3
> > >
> > > L3 module did not seem to have IOS so I ran Xmodem
> > to
> > > put cat4232-in-mz.120-18.W5.22a.bin IOS file on.
> > That
> > > seem to go OK but when resstarted the box, I got
> > the
> > > output below. Any ideas what's going on i.e. why
> > no
> > > CLI is present??
> > >
> > > Compiled Fri 09-Jun-00 10:17 by wkassa
> > > Diagnostic Software (MARINA-DIAG), Version 1.4(1)
> > > [wkassa j_conn]
> > >
> > > Copyright (c) Cisco Systems Inc. 1998-1999
> > >
> > > MARINA>1%
> > > ROMMON: Entered init
> > > ROMMON: Cold Reset frame @0x00000000
> > > ROMMON: Reading reset reason register
> > > ROMMON: Valid NVRAM config
> > >
> > > System Bootstrap, Version 12.0(7)W5(15b) RELEASE
> > > SOFTWARE
> > > Copyright (c) 2000 by cisco Systems, Inc.
> > >
> > > ROMMON: Initializing exceptions
> > > ROMMON: Initializing TLB
> > > ROMMON: Initializing cache
> > > ROMMON: Sizing and zeroing main memory ... 64
> > MBytes
> > > ROMMON: Sizing non-volatile memory ... 128 KBytes
> > > ROMMON: Exiting init
> > >
> > > Catalyst-4232 platform with 65536 Kbytes of main
> > > memory
> > >
> > > Initialize MMC diag test driver
> > > Marina system recognized.
> > > NP54 0, XPIF Ver.1 Port 0 at 1244 M
> > > NP54 0, XPIF Ver.1 Port 1 at 1244 M
> > > NP54 2, XPIF Ver.1 Port 0 at 1244 M
> > > NP54 2, XPIF Ver.1 Port 1 at 1244 M
> > > ****** Spawn status register polling task ******
> > > fpga_ucode begin from 0x8019fe28
> > > FPGA_DNLD completed
> > > Thermostat #0: config reg reads 0x0a
> > > Thermostat #1: config reg reads 0xff
> > >
> > > Booting on Dec 31 1999 23:59:59
> > >
> > > Compiled Fri 09-Jun-00 10:17 by wkassa
> > > Diagnostic Software (MARINA-DIAG), Version 1.4(1)
> > > [wkassa j_conn]
> > >
> > > Copyright (c) Cisco Systems Inc. 1998-1999
> > >
> > > MARINA>1%
> > > ROMMON: Entered init
> > > ROMMON: Cold Reset frame @0x00000000
> > > ROMMON: Reading reset reason register
> > > ROMMON: Valid NVRAM config
> > >
> > > System Bootstrap, Version 12.0(7)W5(15b) RELEASE
> > > SOFTWARE
> > > Copyright (c) 2000 by cisco Systems, Inc.
> > >
> > > ROMMON: Initializing exceptions
> > > ROMMON: Initializing TLB
> > > ROMMON: Initializing cache
> > > ROMMON: Sizing and zeroing main memory ... 64
> > MBytes
> > > ROMMON: Sizing non-volatile memory ... 128 KBytes
> > > ROMMON: Exiting init
> > >
> > > Catalyst-4232 platform with 65536 Kbytes of main
> > > memory
> > >
> > > Initialize MMC diag test driver
> > > Marina system recognized.
> > > NP54 0, XPIF Ver.1 Port 0 at 1244 M
> > > NP54 0, XPIF Ver.1 Port 1 at 1244 M
> > > NP54 2, XPIF Ver.1 Port 0 at 1244 M
> > > NP54 2, XPIF Ver.1 Port 1 at 1244 M
> > > ****** Spawn status register polling task ******
> > > fpga_ucode begin from 0x8019fe28
> > > FPGA_DNLD completed
> > > Thermostat #0: config reg reads 0x0a
> > > Thermostat #1: config reg reads 0xff
> > >
> > > Booting on Dec 31 1999 23:59:59
> > >
> > > Compiled Fri 09-Jun-00 10:17 by wkassa
> > > Diagnostic Software (MARINA-DIAG), Version 1.4(1)
> > > [wkassa j_conn]
> > >
> > > Copyright (c) Cisco Systems Inc. 1998-1999
> > >
> > > MARINA>1%
> > >
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 10:56:53 GMT-3