From: David (david_knot@xxxxxxxxx)
Date: Tue Mar 05 2002 - 07:51:32 GMT-3
What is RMAed?
I think it is in diagnostics mode since I get this
output when I do ?
Any other ideas pls?
MARINA>1% ?
Informational Commands:
Help - Provide Command Help Information
History - Provide Command History Information
Keys - Display Control Keys Usage during
Diagnostics Session
Errorinfo - Display Diagnostics Error Code
information
Version - Display Diagnostics Version information
==============================================================================
Test Execution Commands:
Contents - Provide Diagnostic Test Contents
Information
Set - Set Diagnostic Section/Test Parameter
Values or Date/Time/Prompt
Reset - Reset Diagnostic Section/Test Parameters
to Default Values
Resetmisc - Misc. Reset PHY/gig ports, XPIF Inband,
Link PLD & nP5400s
Unresetmisc- Misc. Unreset PHY/gig ports, XPIF
Inband, Link PLD & nP5400s
Show - Show Diagnostic Section(s)/Test(s)
Parameter Values
Run - Run Diagnostic Section(s)/Test(s)
Skip - Skip Diagnostic Section(s)/Test(s) in
RUN ALL Command
Results - Display Diagnostic Section(s)/Test(s)
Execution Results
Ps - Provide Scheduled Diagnostic Test(s)
Information
Kill - Remove Scheduled Diagnostic Test(s)
==============================================================================
Debug Commands:
Write - Write Data in one or more Address
locations
Read - Read Data from one or more Address
locations
Compare - Compare Data with Contents of one or
more Address locations
Search - Search Data in one or more Address
locations
Verify - Read & Verify Data from one or more
Address locations
Asm - Assemble R5000 instructions in one or
more Memory locations
Dasm - Disassemble R5000 machine codes from one
or more Memory locations
Execute - Execute R5000 machine codes from one or
more Memory locations
Test - Test one Address location performing R/W
Operation
NP54 - Perform NP5400 Debugging Functions
EPc - Perform EPIF/XPIF Debugging Functions
GCam - Perform GigFPGA/TCAM Debugging Functions
EPIFSNAKE - 10/100 Ports Smartbits Snake Test
XPIFSNAKE - Gigabit Ports Smartbits Snake Test
SYSSNAKE - All Ports Smartbits Snake Test
Troubleshoot - Use for fault isolation
==============================================================================
Miscellaneous Commands:
Clear - Clear Screen
Exit - Exit Diagnostic/Debug Session
PowerMargin- Power Supplies Margin Setting
FPGADnld - Download latest FPGA image
DUMPGT - Dump the Galileo registers
MARINA>2%
--- MADMAN <dmadlan@qwest.com> wrote:
>
> Looks like you may have a card that is in
> diagnostic mode. I had a
> 6500 sup card that came up with a funky prompt like
> your seeing, MARINA,
> and I had to get it RMAed. Any Cisco guys out there
> recognize MARINA as
> the L3 card code name???
>
> Dave
>
> David wrote:
> >
> > I'm having issues setting up Cat 4K with L3
> module.
> > This are the modules:
> > Switching Supervisor - WS-X4012
> > Router Switch Card - WS-X4232-L3
> >
> > L3 module did not seem to have IOS so I ran Xmodem
> to
> > put cat4232-in-mz.120-18.W5.22a.bin IOS file on.
> That
> > seem to go OK but when resstarted the box, I got
> the
> > output below. Any ideas what's going on i.e. why
> no
> > CLI is present??
> >
> > Compiled Fri 09-Jun-00 10:17 by wkassa
> > Diagnostic Software (MARINA-DIAG), Version 1.4(1)
> > [wkassa j_conn]
> >
> > Copyright (c) Cisco Systems Inc. 1998-1999
> >
> > MARINA>1%
> > ROMMON: Entered init
> > ROMMON: Cold Reset frame @0x00000000
> > ROMMON: Reading reset reason register
> > ROMMON: Valid NVRAM config
> >
> > System Bootstrap, Version 12.0(7)W5(15b) RELEASE
> > SOFTWARE
> > Copyright (c) 2000 by cisco Systems, Inc.
> >
> > ROMMON: Initializing exceptions
> > ROMMON: Initializing TLB
> > ROMMON: Initializing cache
> > ROMMON: Sizing and zeroing main memory ... 64
> MBytes
> > ROMMON: Sizing non-volatile memory ... 128 KBytes
> > ROMMON: Exiting init
> >
> > Catalyst-4232 platform with 65536 Kbytes of main
> > memory
> >
> > Initialize MMC diag test driver
> > Marina system recognized.
> > NP54 0, XPIF Ver.1 Port 0 at 1244 M
> > NP54 0, XPIF Ver.1 Port 1 at 1244 M
> > NP54 2, XPIF Ver.1 Port 0 at 1244 M
> > NP54 2, XPIF Ver.1 Port 1 at 1244 M
> > ****** Spawn status register polling task ******
> > fpga_ucode begin from 0x8019fe28
> > FPGA_DNLD completed
> > Thermostat #0: config reg reads 0x0a
> > Thermostat #1: config reg reads 0xff
> >
> > Booting on Dec 31 1999 23:59:59
> >
> > Compiled Fri 09-Jun-00 10:17 by wkassa
> > Diagnostic Software (MARINA-DIAG), Version 1.4(1)
> > [wkassa j_conn]
> >
> > Copyright (c) Cisco Systems Inc. 1998-1999
> >
> > MARINA>1%
> > ROMMON: Entered init
> > ROMMON: Cold Reset frame @0x00000000
> > ROMMON: Reading reset reason register
> > ROMMON: Valid NVRAM config
> >
> > System Bootstrap, Version 12.0(7)W5(15b) RELEASE
> > SOFTWARE
> > Copyright (c) 2000 by cisco Systems, Inc.
> >
> > ROMMON: Initializing exceptions
> > ROMMON: Initializing TLB
> > ROMMON: Initializing cache
> > ROMMON: Sizing and zeroing main memory ... 64
> MBytes
> > ROMMON: Sizing non-volatile memory ... 128 KBytes
> > ROMMON: Exiting init
> >
> > Catalyst-4232 platform with 65536 Kbytes of main
> > memory
> >
> > Initialize MMC diag test driver
> > Marina system recognized.
> > NP54 0, XPIF Ver.1 Port 0 at 1244 M
> > NP54 0, XPIF Ver.1 Port 1 at 1244 M
> > NP54 2, XPIF Ver.1 Port 0 at 1244 M
> > NP54 2, XPIF Ver.1 Port 1 at 1244 M
> > ****** Spawn status register polling task ******
> > fpga_ucode begin from 0x8019fe28
> > FPGA_DNLD completed
> > Thermostat #0: config reg reads 0x0a
> > Thermostat #1: config reg reads 0xff
> >
> > Booting on Dec 31 1999 23:59:59
> >
> > Compiled Fri 09-Jun-00 10:17 by wkassa
> > Diagnostic Software (MARINA-DIAG), Version 1.4(1)
> > [wkassa j_conn]
> >
> > Copyright (c) Cisco Systems Inc. 1998-1999
> >
> > MARINA>1%
> >
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 10:56:53 GMT-3