From: John Neiberger (neiby@xxxxxxxxxx)
Date: Sun Mar 03 2002 - 03:13:20 GMT-3
oops....What the heck was I thinking?? That's a sure sign I've
been studying too long today. I know very well the difference
between summary-address and aggregate-address and I still was
using the wrong command! Good grief...
And even while I was typing my first post I had this nagging
feeling that I was overlooking something. :-) Maybe I should
have tried using the BGP area range command. heh heh...
I think I didn't catch my mistake because another router
running 11.2(25a) accepted the command. Now I'm interested to
find out what that particular command is doing.
This is actually one of my biggest worries when I get to the
actual lab. I fear that stuff I've done over and over again
will completely slip my mind.
Okay, I'm done for the night!
Thanks,
John
---- On Sun, 3 Mar 2002, Nigel Taylor
(nigel_taylor@hotmail.com) wrote:
> John,
> You might want to try using the aggregate-address
command and
> see
> what magic happens. As a side note.. IGP's summarize,
whereas BGP being
> an
> EGP aggregates.
>
> watch the word wrap..
>
>
http://www.cisco.com/univercd/cc/td/doc/product/software/ios122/
122cgcr/fipr
> rp_r/bgp_r/1rfbgp1.htm#xtocid1
>
> Nigel
>
> ----- Original Message -----
> From: "John Neiberger" <neiby@ureach.com>
> To: <ccielab@groupstudy.com>
> Sent: Sunday, March 03, 2002 12:30 AM
> Subject: Summarization?? What's that? (bug report)
>
>
> > While attempting to summarize some prefixes in BGP I got the
> > following:
> >
> > R3#conf t
> > Enter configuration commands, one per line. End with
CNTL/Z.
> > R3(config)#router bgp 2010
> > R3(config-router)#summa?
> > % Unrecognized command
> > R3(config-router)#summar?
> > % Unrecognized command
> > R3(config-router)#summar
> > ^
> > % Invalid input detected at '^' marker.
> >
> > R3(config-router)#?
> > Router configuration commands:
> > address-family Enter Address Family command mode
> > aggregate-address Configure BGP aggregate entries
> > auto-summary Enable automatic network number
> > summarization
> > bgp BGP specific commands
> > default Set a command to its defaults
> > default-information Control distribution of default
> > information
> > default-metric Set metric of redistributed routes
> > distance Define an administrative distance
> > distribute-list Filter networks in routing updates
> > exit Exit from routing protocol
configuration
> > mode
> > help Description of the interactive help
> > system
> > maximum-paths Forward packets over multiple paths
> > neighbor Specify a neighbor router
> > network Specify a network to announce via BGP
> > no Negate a command or set its defaults
> > redistribute Redistribute information from another
> > routing protocol
> > synchronization Perform IGP synchronization
> > table-map Map external entry attributes into
> > routing table
> > timers Adjust routing timers
> >
> > R3(config-router)#
> >
> > I'm thinking it might be tough to do summarization when the
> > freaking command is missing!!
> >
> > This is a 2500 running 12.1(11) Enterprise Plus. Too
weird. I
> > didn't find a bug report for it on CCO but I can't be the
only
> > person to run into this.
> >
> > Since I don't feel like doing un upgrade right now, I'll
skip
> > that part. <g>
> >
> > John
> >
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 10:56:51 GMT-3