From: JOSE ANGEL MARTINEZ DE LA VARA (jamartinez@xxxxxxxxxxxxxxxx)
Date: Mon Feb 04 2002 - 11:55:11 GMT-3
Yes, I had seen that before and I applied it without the dialerstring
command because there was no number to dial (you know, back-to-back). Is it
mandatory?
-----Mensaje original-----
De: Erhan Kurt [mailto:iekurt@yahoo.com]
Enviado el: lunes, 04 de febrero de 2002 15:48
Para: JOSE ANGEL MARTINEZ DE LA VARA; ccielab@groupstudy.com
Asunto: RE: AUX to AUX Dialer - as ISDN
Yeah, it also worked. The config was like:
http://www.cisco.com/warp/public/471/mod-aux-dialout.html#configs
--- JOSE ANGEL MARTINEZ DE LA VARA
<jamartinez@landata.payma.es> wrote:
> Yes, that works. Did you try with Dialer interfaces?
>
> -----Mensaje original-----
> De: Erhan Kurt [mailto:iekurt@yahoo.com]
> Enviado el: lunes, 04 de febrero de 2002 15:25
> Para: JOSE ANGEL MARTINEZ DE LA VARA;
> ccielab@groupstudy.com
> Asunto: RE: AUX to AUX Dialer - as ISDN
>
>
>
> Hi All,
>
> Below config works well with a rollover cable.
>
> Caller:
> interface Async241
> ip address 192.168.1.1 255.255.255.0
> encapsulation ppp
> ip ospf demand-circuit
> dialer in-band
> dialer-group 1
> async default routing
> async dynamic routing
> async mode dedicated
> ipx network 63
> no ipx route-cache
> no fair-queue
> no cdp enable
> ppp authentication chap callin
> !
>
> Called:
> interface Async241
> ip address 192.168.1.2 255.255.255.0
> encapsulation ppp
> ip ospf network point-to-point
> ip ospf demand-circuit
> async default routing
> async dynamic routing
> async mode dedicated
> ipx network 63
> no fair-queue
> no cdp enable
> ppp authentication chap
> !
>
>
> Cheers,
> Erhan
>
>
> --- JOSE ANGEL MARTINEZ DE LA VARA
> <jamartinez@landata.payma.es> wrote:
> > Hi,
> >
> > I've tried that and works with a roll-over cable
> > (cisco console cable). You
> > have to create the async interface with the number
> > os line for the aux shown
> > in the show line command. I think it is
> > automatically created when you enter
> > the command modem inout in the line.
> >
> > After those commands and some more that you can
> find
> > at cco
> >
>
http://www.cisco.com/warp/public/793/access_dial/auxback.html
> > and
> > successfull ping when cofiguring the physical
> > interface as Legacy-DDR, the I
> > tried to use Dialer and never worked. Never
> > apperared the dialer bind to the
> > physical interface when pinging as before with
> debug
> > dialer enabled.
> >
> > Tell me if you succed.
> >
> > Good luck
> >
> > Jose Angel
> >
> > -----Mensaje original-----
> > De: Carl Phelan [mailto:carlphelan@hotmail.com]
> > Enviado el: viernes, 01 de febrero de 2002 20:47
> > Para: ccielab@groupstudy.com
> > Asunto: AUX to AUX Dialer - as ISDN
> >
> >
> > Hi,
> >
> > It's probably been discussed many times already
> but
> > not easily found in
> > the archives.
> >
> > I'm looking for the best configuration or paper
> that
> > will show how to
> > simulate ISDN callout as near as possible over an
> > AUX to AUX connection
> > - I understand with a straight through cable. If
> > possible, it will
> > allow you work up through layers 2 and 3.
> >
> > Many thanks.
> >
> > Carl.
> >
>
This archive was generated by hypermail 2.1.4 : Thu Jun 20 2002 - 13:46:11 GMT-3