From: Wen Jia Yang (tonyblair@xxxxxxxxx)
Date: Fri Feb 01 2002 - 04:45:27 GMT-3
Thanks for your help,but I still couldn't ping,all the status are up/up,I can p
ing the ethernet interface ip address ,but couldn't
PING the other side.
the configuration file is as followed.
Current configuration:
!
version 11.2
no service pad
no service udp-small-servers
no service tcp-small-servers
!
hostname Switch
!
!
!
!
interface VLAN1
no ip route-cache
!
interface FastEthernet0/1
!
interface FastEthernet0/2
!
interface FastEthernet0/3
!
interface FastEthernet0/4
nterface FastEthernet0/5
!
interface FastEthernet0/6
!
interface FastEthernet0/7
!
interface FastEthernet0/8
!
interface FastEthernet0/9
!
interface FastEthernet0/10
!
interface FastEthernet0/11
!
interface FastEthernet0/12
!
interface FastEthernet0/13
!
interface FastEthernet0/14
!
interface FastEthernet0/15
!
interface FastEthernet0/16
!
!
line con 0
stopbits 1
line vty 0 4
login
!
end
pls help,thanks in advance.
----- Original Message -----
From: "Manny Gonzalez" <manny@nyp.org>
To: "Chua, Parry" <Parry.Chua@compaq.com>
Cc: "Wen Jia Yang" <tonyblair@etang.com>; <ccielab@groupstudy.com>
Sent: Friday, February 01, 2002 2:32 PM
Subject: Re: how to make a catalyst 2916m xl switch to be a hub
> As per Cisco, all Catalyst switches are PLUG-N-PLAY out of the box.
> Basically all ports are in VLAN 1 and enabled.. so you should be able to
> get it to work. If in doubt, do a ERASE START and RELOAD and then try it
> again...
>
> You should have nothing to do except address the router interfaces to
> get them to ping each other...
>
> This may be insulting to you, but I do it all the time. Did you NO SHUT
> the Ethernets on the router? :-))
>
> "Chua, Parry" wrote:
> >
> > Are you try to setup something like ....
> >
> > (R1)-e0----port1<2916>port2---e0-(R2),
> >
> > In this case, port 1 and 2 of 2916 should be in the same vlan if R1 e0
> > and R2 e0 is on the same subnet.
> >
> > I think you can do a show run to check the current configuration.
> > I presume all ports are in vlan 1 (default).
> > Next you want to create several vlans, thena assign ports to vlan, then
> > assisgn ip address
> > to each vlan and then setup routing protocols on vlan's.
> >
> > >From the doc, to assign port to vlan : ( note that there are several
> > ways to assign a port
> > to vlan(s). Below is static assignment.
> >
> > steps:
> > 1. conf t
> > 2. interface xx
> > 3. switchport mode access
> > 4. switchport access vlan 2 ! assign port xx to valn 2
> > 5. exit
> > 6, show run
> >
> > Parry Chua
> >
> > -----Original Message-----
> > From: Wen Jia Yang [mailto:tonyblair@etang.com]
> > Sent: Friday, February 01, 2002 10:12 AM
> > To: ccielab@groupstudy.com
> > Subject: how to make a catalyst 2916m xl switch to be a hub
> >
> > I tried to make the switch (factory default value)to work as a hub for
> > ethernet connections between ether interfaces of routers.
> >
> > Do I need some extra configurations?
> > I tried to use it as it was,But I couldn't ping the other side router
> > through a switch.
> > Can you help me?
> > Thanks in advance.
This archive was generated by hypermail 2.1.4 : Thu Jun 20 2002 - 13:46:09 GMT-3