From: fwells12 (fwells12@xxxxxxxxxxx)
Date: Fri Nov 30 2001 - 05:57:19 GMT-3
If you ever have a piece of Cisco hardware that does not show all its
interfaces it is almost certainly that it does not have enough DRAM in it,
or the version of IOS on it does not support that hardware. The
hardware-software compatibility matrix on CCO will point out the latter -and
sometimes the former!
Anyway, your 2509 will run ANY version of IOS you want so long as you give
it enough memory. If it is CiscoPro equipment, upgrade its BIOS image with
the RSL software on CCO. Once you have done that it will run any code the
regular routers will run.
----- Original Message -----
From: "DAN DORTON" <DHSTS68@dhs.state.il.us>
To: <ccielab@groupstudy.com>; <bobdixon@mediaone.net>
Cc: <brian@5g.net>; <lachisho@tnc.com>
Sent: Thursday, November 29, 2001 1:05 PM
Subject: Re: 2509AS
> Thanks Bob I will try this.
> It still confuses me that the router can still use the async ports, but
not recognize them in the config?
>
> >>> "Bob Dixon" <bobdixon@mediaone.net> 11/29/01 03:01PM >>>
> Folks,
>
> I just did this at home. The curiousity was killing me. I have the async
> ports on my 2509 configured and working and I was able to enable bgp and
> ospf on it.
>
> Thanks,
> Bob
>
> Here are the details:
>
> ts#sh run
> Building configuration...
>
> Current configuration:
> !
> version 12.0
> service timestamps debug uptime
> service timestamps log uptime
> no service password-encryption
> !
> hostname ts
> !
> no logging on
> enable secret 5 xxxx
> !
> ip subnet-zero
> no ip domain-lookup
> ip host r1 2001 1.1.1.1
> ip host r2 2002 1.1.1.1
> ip host r3 2003 1.1.1.1
> ip host fr 2004 1.1.1.1
> ip host r4 2005 1.1.1.1
> ip host r5 2006 1.1.1.1
> ip host r6 2007 1.1.1.1
> ip host sw 2008 1.1.1.1
> !
> !
> clock timezone EST -5
> clock summer-time EST recurring
> !
> !
> !
> interface Loopback0
> ip address 1.1.1.1 255.255.255.0
> no ip directed-broadcast
> !
> interface Ethernet0
> ip address 10.0.0.1 255.255.255.0
> no ip directed-broadcast
> !
> interface Serial0
> no ip address
> no ip directed-broadcast
> shutdown
> clockrate 4000000
> !
> interface Serial1
> no ip address
> no ip directed-broadcast
> shutdown
> !
> router ospf 1
> !
> router rip
> network 10.0.0.0
> !
> router bgp 1
> !
> ip default-gateway 10.0.0.4
> ip classless
> ip route 0.0.0.0 0.0.0.0 10.0.0.4
> !
> logging trap debugging
> logging 10.0.0.2
> access-list 3 permit 10.0.0.0 0.0.0.255
> !
> tftp-server flash c2500-jos56i-l.120-14.bin
> !
> line con 0
> exec-timeout 0 0
> password 7 xxxx
> login
> transport input none
> line 1 8
> no exec
> transport input all
> line aux 0
> line vty 0 4
> exec-timeout 0 0
> login local
> !
> end
>
> ts#sh ver
> Cisco Internetwork Operating System Software
> IOS (tm) 2500 Software (C2500-JOS56I-L), Version 12.0(14), RELEASE
> SOFTWARE (fc1)
> Copyright (c) 1986-2000 by cisco Systems, Inc.
> Compiled Tue 31-Oct-00 22:06 by linda
> Image text-base: 0x030581DC, data-base: 0x00001000
>
> ROM: System Bootstrap, Version 5.2(8a), RELEASE SOFTWARE
> BOOTFLASH: 3000 Bootstrap Software (IGS-RXBOOT), Version 10.2(8a),
> RELEASE SOFTWARE (fc1)
>
> ts uptime is 3 minutes
> System restarted by power-on
> System image file is "flash:c2500-jos56i-l.120-14.bin"
>
> cisco 2509 (68030) processor (revision D) with 16384K/2048K bytes of
> memory.
> Processor board ID 04151749, with hardware revision 00000000
> Bridging software.
> X.25 software, Version 3.0.0.
> SuperLAT software (copyright 1990 by Meridian Technology Corp).
> TN3270 Emulation software.
> 1 Ethernet/IEEE 802.3 interface(s)
> 2 Serial network interface(s)
> 8 terminal line(s)
> 32K bytes of non-volatile configuration memory.
> 16384K bytes of processor board System flash (Read ONLY)
>
> Configuration register is 0x2102
>
> ----- Original Message -----
> From: DAN DORTON <DHSTS68@dhs.state.il.us>
> To: <ccielab@groupstudy.com>; <eteisbe@qwest.com>
> Sent: Thursday, November 29, 2001 2:45 PM
> Subject: RE: 2509AS
>
>
> > Ok I guess what I am trying to do is still utilize the async ports on
> this router as my terminal server, but also use the ethernet & serial
> interface for routing OSPF.
> >
> > Unless I have the remote access server software (Which apparently does
> not support OSPF, or BGP) my async ports do not show up as configurable.
> >
> > I have tried many standard 2500 series softwares that do support all
> thge protocols, but they do not support all my interfaces.
> >
> > I really don't need a memory upgrade on this one, because it is mainly
> my terminal server & I only use one interface on it in my lab.
> >
> > I have 8 other routers in my lab that will run anything, but I just
> needed this AS2509 interface also for this scenario.
> >
> > I have redsigned the lab now where I only need to run IGRP over this
> link, so I am fine.
> >
> > Thanks for all the input though.
> >
> > Dan
> >
> > >>> "Teisberg, Evan" <eteisbe@qwest.com> 11/29/01 01:40PM >>>
> > Dan,
> >
> > I may be way off here... but I seem to remember seeing this (OSPF at
> least)
> > when there was not at least ONE interface configured for IP and in an
> UP/UP
> > state. You could do a "no keepalive" on an ethernet interface
> configured
> > with an IP address and try again.
> >
> > I don't know if this is the issue, but that fact that you have the BGP
> and
> > OSPF commands available makes me think it is a possibility.
> >
> > HTH
> > -Evan.
> >
> >
> >
> > -----Original Message-----
> > From: DAN DORTON [mailto:DHSTS68@dhs.state.il.us]
> > Sent: Thursday, November 29, 2001 12:38 PM
> > To: brian@5g.net; ccielab@groupstudy.com
> > Subject: RE: 2509AS
> >
> >
> > This is an 2509 remote access server.
> >
> > When I try to configure OSPF, or BGP on the router it says unknown
> routing
> > protocol.
> >
> > Although I can configure RIP, IGRP, or EIGRP.
> >
> > Memory has nothing to do with it.
> >
> > When I do a router ? under the config it shows OSPF & BGP, but it will
> not
> > allow you to configure them.
> >
> > I repeat TAC says these two protocols are unsupported on this unit.
> >
> > Thanks,
> >
> >
> > >>> "Brian Dennis" <brian@5g.net> 11/29/01 12:12PM >>>
> > Dan,
> > A 2509 will support BGP and OSPF. I think TAC must not have understand
> what
> > you were asking.
> >
> > Brian Dennis, CCIE #2210 (R&S)(ISP/Dial) CCSI #98640
> > 5G Networks, Inc.
> > bdennis@5g.net
> >
> >
> > -----Original Message-----
> > From: nobody@groupstudy.com [mailto:nobody@groupstudy.com]On Behalf Of
> > DAN DORTON
> > Sent: Thursday, November 29, 2001 9:41 AM
> > To: DAN DORTON; ccielab@groupstudy.com
> > Subject: Re: 2509AS
> >
> >
> > Nevermind. TAC answered my question.
> >
> > Apparently the BGP & OSPF processes are too CPU intensive for that
> unit &
> > are unsupported.
> >
> > Thanks anyways,
> >
> >
> > >>> "DAN DORTON" <DHSTS68@dhs.state.il.us> 11/29/01 11:13AM >>>
> > I am having trouble finding an IOS that supports OSPF & BGP routing on
> my
> > 2509AS.
> >
> > It only has 8MB flash & 4MB ram.
> >
> > Am I missing something here? It will use RIP & EIGRP.
> >
> > Thanks in advance.
This archive was generated by hypermail 2.1.4 : Fri Jun 21 2002 - 06:45:27 GMT-3