From: Brion Washington (CCIE6200@xxxxxxxx)
Date: Wed Nov 28 2001 - 18:17:27 GMT-3
Your config is wrong. You need to change source-bridge remote-peer 12 tcp
130.13.5.4 on R4 to source-bridge local-peer peer-id 130.13.5.4, and change
R3 source-bridge remote-peer 12 tcp 130.13.1.1 to source-bridge local-peer
peer-id 130.13.1.1
So basically you are using two remote-peer statements. You can forgo the
remote-peer one one side if you use Promiscuous at the end of the local-peer
statement.
This should get you working fast.
Brion
-----Original Message-----
From: nobody@groupstudy.com [mailto:nobody@groupstudy.com]On Behalf Of
Lupi, Guy
Sent: Wednesday, November 28, 2001 1:44 PM
To: 'ccielab@groupstudy.com'
Subject: Source Route Bridging
Ok, I started out with this elaborate set up, 6 routers, source route and
remote source route bridging, first time trying it. I steadily removed
routers until I am down to 2 and I still can't get it to work!!! I have 2
routers, each with one token ring interface and one serial interface, the
serial interfaces connect the 2 routers. I looked on CCO, verified that
everything looks correct, yet I can never get the 2 remote peers to go into
an open state. Below are the configs, an extended ping to show
connectivity, and the output of a show source from each router. I would
really appreciate it if someone could take a look and let me know what I am
doing wrong, thanks.
R4#sh run
Building configuration...
Current configuration:
!
version 12.0
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname R4
!
!
ip subnet-zero
!
!
!
source-bridge ring-group 12
source-bridge remote-peer 12 tcp 130.13.5.4
source-bridge remote-peer 12 tcp 130.13.1.1
!
!
interface Serial0
ip address 4.4.4.4 255.255.255.0
no ip directed-broadcast
ip ospf interface-retry 0
no ip mroute-cache
no fair-queue
!
interface Serial1
no ip address
no ip directed-broadcast
shutdown
!
interface TokenRing0
ip address 130.13.5.4 255.255.255.0
no ip directed-broadcast
ip ospf interface-retry 0
ring-speed 16
multiring ip
source-bridge 2 1 12
source-bridge spanning
!
interface BRI0
no ip address
no ip directed-broadcast
shutdown
!
router ospf 100
network 4.4.4.0 0.0.0.255 area 0
network 130.13.5.0 0.0.0.255 area 0
!
ip classless
!
!
!
line con 0
transport input none
line aux 0
line vty 0 4
login
!
end
R4#
R4#ping
Protocol [ip]:
Target IP address: 130.13.1.1
Repeat count [5]:
Datagram size [100]:
Timeout in seconds [2]:
Extended commands [n]: y
Source address or interface: 130.13.5.4
Type of service [0]:
Set DF bit in IP header? [no]:
Validate reply data? [no]:
Data pattern [0xABCD]:
Loose, Strict, Record, Timestamp, Verbose[none]:
Sweep range of sizes [n]:
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 130.13.1.1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 4/4/8 ms
R4#
R4#sh source
Local Interfaces: receive transmit
srn bn trn r p s n max hops cnt cnt drops
To0 2 2 12 * b 7 7 7 0 0 0
Global RSRB Parameters:
TCP Queue Length maximum: 100
Ring Group 12:
This TCP peer: 130.13.5.4
Maximum output TCP queue length, per peer: 100
Peers: state bg lv pkts_rx pkts_tx expl_gn drops
TCP
TCP 130.13.5.4 - 3 0 0 0 0
0
TCP 130.13.1.1 closed 3 0 0 0 0
0
Rings:
bn: 2 rn: 2 local ma: 4008.de5c.a38a TokenRing0 fwd: 0
Explorers: ------- input ------- ------- output -------
spanning all-rings total spanning all-rings total
To0 0 0 0 0 0 0
Explorer fastswitching enabled
Local switched: 0 flushed 0 max Bps 38400
rings inputs bursts throttles output drops
To0 0 0 0 0
R4#
R3#sh run
Building configuration...
Current configuration:
!
version 12.0
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname R3
!
!
ip subnet-zero
!
!
!
source-bridge ring-group 12
source-bridge remote-peer 12 tcp 130.13.1.1
source-bridge remote-peer 12 tcp 130.13.5.4
!
!
interface Serial0
ip address 4.4.4.5 255.255.255.0
no ip directed-broadcast
ip ospf interface-retry 0
no ip mroute-cache
no fair-queue
clockrate 1300000
!
interface Serial1
no ip address
no ip directed-broadcast
shutdown
!
interface TokenRing0
ip address 130.13.1.1 255.255.255.0
no ip directed-broadcast
ip ospf interface-retry 0
ring-speed 16
multiring ip
source-bridge 1 1 12
source-bridge spanning
!
interface BRI0
no ip address
no ip directed-broadcast
shutdown
!
router ospf 100
network 4.4.4.0 0.0.0.255 area 0
network 130.13.1.0 0.0.0.255 area 0
!
ip classless
!
!
!
line con 0
transport input none
line aux 0
line vty 0 4
login
!
end
R3#
R3#ping
Protocol [ip]:
Target IP address: 130.13.5.4
Repeat count [5]:
Datagram size [100]:
Timeout in seconds [2]:
Extended commands [n]: y
Source address or interface: 130.13.1.1
Type of service [0]:
Set DF bit in IP header? [no]:
Validate reply data? [no]:
Data pattern [0xABCD]:
Loose, Strict, Record, Timestamp, Verbose[none]:
Sweep range of sizes [n]:
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 130.13.5.4, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 4/9/28 ms
R3#
R3#sh sour
Local Interfaces: receive transmit
srn bn trn r p s n max hops cnt cnt drops
To0 1 1 12 * f 7 7 7 0 0 0
Global RSRB Parameters:
TCP Queue Length maximum: 100
Ring Group 12:
This TCP peer: 130.13.1.1
Maximum output TCP queue length, per peer: 100
Peers: state bg lv pkts_rx pkts_tx expl_gn drops
TCP
TCP 130.13.1.1 - 3 0 0 0 0
0
TCP 130.13.5.4 closed 3 0 0 0 0
0
Rings:
bn: 1 rn: 1 local ma: 4008.de6c.6382 TokenRing0 fwd: 0
Explorers: ------- input ------- ------- output -------
spanning all-rings total spanning all-rings total
To0 0 0 0 0 0 0
Explorer fastswitching enabled
Local switched: 0 flushed 0 max Bps 38400
rings inputs bursts throttles output drops
To0 0 0 0 0
R3#
This archive was generated by hypermail 2.1.4 : Fri Jun 21 2002 - 06:45:24 GMT-3