From: xander (xander@xxxxxx)
Date: Fri Nov 23 2001 - 11:12:23 GMT-3
Hello michael,
You need to setup ilmi pvc instead of qsaal to inform LS1010 to
register end-points.
Friday, November 23, 2001, 9:17:52 AM, you wrote:
mr> Hi, Frank
mr> yes, show atm ilmi-status
mr> you will find the prefix NSAP
mr> regards
mr> michael
mr> --- Frank Kim <frank@comegetus.com> wrote:
>> Michael,
>> Let's say if you don't have access to the switch to
>> figure out what the
>> nsap address is, is there a command in the router
>> where you can run to
>> figure out what is the nsap or esi address? Thanks.
>>
>>
>> -Frank
>>
>> On Fri, 23 Nov 2001,
>> michael robertson wrote:
>>
>> > Dear group,
>> >
>> > I have practiced atm lately, and the atm switch
>> is
>> > lightstream 1010.
>> >
>> > I have tried to assign the atm nsap address with
>> esi
>> > address, I can ping between two routers, If I
>> assign
>> > the atm nsap address with the following command,
>> > atm nsap-address
>> > 47.009181000000001007386501.888888888888.00 ,
>> >
>> > then I have no luck to ping other side. I debug
>> atm
>> > signal, and it says that E164 is not converted. In
>> > this scenario, does this mean that lightstream
>> can't
>> > allow youself to assign your own atm address and
>> the
>> > only way you have to do is use atm esi address??
>> >
>> > Question 2:
>> >
>> > If I can assign atm nsap address, the first 13
>> bytes
>> > should be identical to ATM switch or not?
>> >
>> >
>> > Regards
>> >
>> > michael
>> >
>> >
>> > ------R1-------ATM lightstream 1010------R2----
>> >
>> >
>> >
>> >
>> > Configuration is as follows:
>> >
>> > R1
>> >
>> > r1#sh run int atm2/0
>> > Building configuration...
>> >
>> > Current configuration:
>> > !
>> > interface ATM2/0
>> > ip address 200.10.11.16 255.255.255.0
>> >
>> > map-group 1483svc
>> > atm nsap-address
>> > 47.009181000000001007386501.999999999999.00
>> > no atm scrambling cell-payload
>> > atm pvc 5 0 5 qsaal
>> > no atm ilmi-keepalive
>> > end
>> >
>> > map-list 1483svc
>> > ip 200.10.11.15 atm-nsap
>> > 47.009181000000001007386501.888888888888.00
>> broadcast
>> >
>> > -------------------------------
>> >
>> > R2:
>> >
>> > interface ATM2/0
>> > ip address 200.10.11.15 255.255.255.0
>> > map-group 1483svc
>> > atm nsap-address
>> > 47.009181000000001007386501.888888888888.00
>> > no atm scrambling cell-payload
>> > atm pvc 5 0 5 qsaal
>> > no atm ilmi-keepalive
>> > end
>> >
>> > map-list 1483svc
>> > ip 200.10.11.16 atm-nsap
>> > 47.009181000000001007386501.999999999999.00
>> broadcast
>> >
>> >
>> >
>> >
>>
This archive was generated by hypermail 2.1.4 : Fri Jun 21 2002 - 06:45:21 GMT-3