From: Dennis #6 (vacant@xxxxxxxx)
Date: Tue Nov 13 2001 - 11:49:32 GMT-3
Addition to my previous comment... The default-information originate command
under bgp works fine for me. Its when I add it to the end of a neighbor
statement that it crashes the router.... every time. Anyone else seen this?
R1(config-router)#neighbor 137.20.10.70 default-originate
R1(config-router)#
=== Flushing messages (00:38:29 UTC Mon Mar 1 1993) ===
Buffered messages:
00:00:08: %LINK-3-UPDOWN: Interface Ethernet0, changed state to up
00:00:08: %LINK-3-UPDOWN: Interface Ethernet1, changed state to up
00:00:09: %LINK-3-UPDOWN: Interface Serial0, changed state to up
00:00:09: %LINK-3-UPDOWN: Interface Serial1, changed state to down
00:00:10: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0, changed
state to up
*Mar 1 00:01:37.075: %LINEPROTO-5-UPDOWN: Line protocol on Interface
Ethernet0, changed state to up
*Mar 1 00:01:37.079: %LINEPROTO-5-UPDOWN: Line protocol on Interface
Ethernet1, changed state to down
*Mar 1 00:01:39.115: %LINEPROTO-5-UPDOWN: Line protocol on Interface
Serial0, changed state to up
*Mar 1 00:01:41.739: %LINK-5-CHANGED: Interface Ethernet1, changed state to
administratively down
*Mar 1 00:01:43.675: %LINK-5-CHANGED: Interface Serial1, changed state to
administratively down
*Mar 1 00:01:44.119: %SYS-5-CONFIG_I: Configured from memory by console
*Mar 1 00:01:44.719: %LINEPROTO-5-UPDOWN: Line protocol on Interface
Serial1, changed state to down
*Mar 1 00:02:28.663: %SYS-5-RESTART: System restarted --
Cisco Internetwork Operating System Software
IOS (tm) 2500 Software (C2500-JOS56I-L), Version 12.1(9), RELEASE SOFTWARE
(fc1)
Copyright (c) 1986-2001 by cisco Systems, Inc.
Compiled Wed 13-Jun-01 12:21 by kellythw
*Mar 1 00:02:38.123: %OSPF-5-ADJCHG: Process 1, Nbr 137.20.240.1 on Serial0
from LOADING to FULL, Loading Done
*Mar 1 00:02:58.143: %BGP-5-ADJCHANGE: neighbor 137.20.10.70 Up
*Mar 1 00:03:04.215: %BGP-5-ADJCHANGE: neighbor 137.20.100.33 Up
*Mar 1 00:03:24.723: %BGP-5-ADJCHANGE: neighbor 137.20.60.1 Up
*Mar 1 00:37:14.435: %SYS-5-CONFIG_I: Configured from console by console
Queued messages:
Exception: Illegal Instruction at 0x0 (PC)
System Bootstrap, Version 11.0(10c), SOFTWARE
Copyright (c) 1986-1996 by cisco Systems
2500 processor with 14336 Kbytes of main memory
After reboot...................
R1#sh ver
Cisco Internetwork Operating System Software
IOS (tm) 2500 Software (C2500-JOS56I-L), Version 12.1(9), RELEASE SOFTWARE
(fc1)
Copyright (c) 1986-2001 by cisco Systems, Inc.
Compiled Wed 13-Jun-01 12:21 by kellythw
Image text-base: 0x0307DAFC, data-base: 0x00001000
ROM: System Bootstrap, Version 11.0(10c), SOFTWARE
BOOTLDR: 3000 Bootstrap Software (IGS-BOOT-R), Version 11.0(10c), RELEASE
SOFTWARE (fc1)
R1 uptime is 3 minutes
System returned to ROM by error - Illegal Instruction, PC 0x0
System image file is "flash:/c2500-jos56i-l.121-9.bin"
cisco 2500 (68030) processor (revision L) with 14336K/2048K bytes of memory.
Processor board ID 10678953, with hardware revision 00000000
Bridging software.
X.25 software, Version 3.0.0.
SuperLAT software (copyright 1990 by Meridian Technology Corp).
TN3270 Emulation software.
2 Ethernet/IEEE 802.3 interface(s)
2 Serial network interface(s)
32K bytes of non-volatile configuration memory.
16384K bytes of processor board System flash (Read ONLY)
Configuration register is 0x2102
-----Original Message-----
From: nobody@groupstudy.com [mailto:nobody@groupstudy.com]On Behalf Of
Thekkethala
Sent: Tuesday, November 13, 2001 12:25 AM
To: ccielab@groupstudy.com
Subject: Router reboot : BGp default originate
Anyone had a router reset when the bgp Default Originate command was issued
in
the config
the IOS version I am running is 12.1(5)T9
I have tried this in 3 routers with the same problem so I am sure its not a
hardware issue - ???
any suggested patches or workarounds !!
This archive was generated by hypermail 2.1.4 : Fri Jun 21 2002 - 06:45:14 GMT-3