From: Ravi (s_ravichandran@xxxxxxxxxxx)
Date: Tue Oct 23 2001 - 12:00:49 GMT-3
Rich,
So, what is the answer for my example? will that bring up the second channel
or not?
Regards,
Ravi
----- Original Message -----
From: Richard Gallagher <rgallagh@cisco.com>
To: Ravi <s_ravichandran@hotmail.com>; routerjocky <elouie@yahoo.com>;
<ccielab@groupstudy.com>
Sent: Tuesday, October 23, 2001 12:24 PM
Subject: Re: dialer load-threshold
> Ravi,
>
> If one sides transmit rate reaches more than 128/255 x 64K then the the
second
> B channel will be bought up.
>
> Rich
>
> CCIE# 7211
>
> On Oct 23, 4:17pm, Ravi chatted about:
> > Subject:Re: dialer load-threshold
> > Still I am confused.
> >
> > Let us consider the following example.
> >
> > ppp multilink
> > dialer load-threshold 128 either
> >
> > 1) if the outbound load is 50k and inbound load is 46k, will this bring
up
> > the second bri?
> >
> > Regards,
> > Ravi
> >
> >
> >
> >
> >
> >
> > ----- Original Message -----
> > From: routerjocky <elouie@yahoo.com>
> > To: Ravi <s_ravichandran@hotmail.com>; <ccielab@groupstudy.com>
> > Sent: Tuesday, October 23, 2001 9:51 AM
> > Subject: Re: dialer load-threshold
> >
> >
> > > > Can you tell me What is the meaning of either?
> > > Hey, Ravi...
> > >
> > > it means either inbound and outbound
> > >
> > > >
> > > >
> > > >
> > > > Regards,
> > > > Ravi
> > > >
> > > > ----- Original Message -----
> > > > From: John Kim <albugkim@hotmail.com>
> > > > To: <s_ravichandran@hotmail.com>; <ccielab@groupstudy.com>
> > > > Sent: Tuesday, October 23, 2001 9:23 AM
> > > > Subject: Re: dialer load-threshold
> > > >
> > > >
> > > > > Ravi,
> > > > >
> > > > > The default is outbound and you can see that by sh run command.
> > > > >
> > > > > Thanks,
> > > > > John Kim
> > > > >
> > > > >
> > > > > >From: "Ravi" <s_ravichandran@hotmail.com>
> > > > > >Reply-To: "Ravi" <s_ravichandran@hotmail.com>
> > > > > >To: <ccielab@groupstudy.com>
> > > > > >Subject: dialer load-threshold
> > > > > >Date: Tue, 23 Oct 2001 09:08:50 -0400
> > > > > >
> > > > > >Hi,
> > > > > >
> > > > > >When entering dialer load threshold command, there are four
options.
> > > > > >
> > > > > >1) either
> > > > > >2) inbound
> > > > > >3) outbound
> > > > > >4) cr
> > > > > >
> > > > > >can anyone let me know what is cr? in other words, what is the
> > default?
> > > > > >
> > > > > >Also either means whether the addition of both inbound and
outbound
> > > > > >traffic?
> > > > > >
> > > > > >How can I verify?
> > > > > >
> > > > > >
> > > > > >Regards,
> > > > > >Ravi
This archive was generated by hypermail 2.1.4 : Thu Jun 20 2002 - 22:33:23 GMT-3