From: Ravi (s_ravichandran@xxxxxxxxxxx)
Date: Tue Oct 23 2001 - 11:59:51 GMT-3
Rob,
I am also thinking the same.(that means my example should not bring up the
second channel) But do you have any Cisco documentation to confirm this.
Regards,
Ravi
----- Original Message -----
From: Roberto Kratzo <roberto_dikratzo@demanet.com>
To: Ravi <s_ravichandran@hotmail.com>; routerjocky <elouie@yahoo.com>;
<ccielab@groupstudy.com>
Sent: Tuesday, October 23, 2001 10:25 AM
Subject: RE: dialer load-threshold
> either means "in" OR "out".
> so the threshold must be reached on inbound OR on outbound.
>
> Rob
>
> -----Original Message-----
> From: nobody@groupstudy.com [mailto:nobody@groupstudy.com]On Behalf Of
> Ravi
> Sent: 23 October 2001 16:13
> To: routerjocky; ccielab@groupstudy.com
> Subject: Re: dialer load-threshold
>
>
> Still I am confused.
>
> Let us consider the following example.
>
> ppp multilink
> dialer load-threshold 128 either
>
> 1) if the outbound load is 50k and inbound load is 46k, will this bring up
> the second bri?
>
> Regards,
> Ravi
>
>
>
>
>
>
> ----- Original Message -----
> From: routerjocky <elouie@yahoo.com>
> To: Ravi <s_ravichandran@hotmail.com>; <ccielab@groupstudy.com>
> Sent: Tuesday, October 23, 2001 9:51 AM
> Subject: Re: dialer load-threshold
>
>
> > > Can you tell me What is the meaning of either?
> > Hey, Ravi...
> >
> > it means either inbound and outbound
> >
> > >
> > >
> > >
> > > Regards,
> > > Ravi
> > >
> > > ----- Original Message -----
> > > From: John Kim <albugkim@hotmail.com>
> > > To: <s_ravichandran@hotmail.com>; <ccielab@groupstudy.com>
> > > Sent: Tuesday, October 23, 2001 9:23 AM
> > > Subject: Re: dialer load-threshold
> > >
> > >
> > > > Ravi,
> > > >
> > > > The default is outbound and you can see that by sh run command.
> > > >
> > > > Thanks,
> > > > John Kim
> > > >
> > > >
> > > > >From: "Ravi" <s_ravichandran@hotmail.com>
> > > > >Reply-To: "Ravi" <s_ravichandran@hotmail.com>
> > > > >To: <ccielab@groupstudy.com>
> > > > >Subject: dialer load-threshold
> > > > >Date: Tue, 23 Oct 2001 09:08:50 -0400
> > > > >
> > > > >Hi,
> > > > >
> > > > >When entering dialer load threshold command, there are four
options.
> > > > >
> > > > >1) either
> > > > >2) inbound
> > > > >3) outbound
> > > > >4) cr
> > > > >
> > > > >can anyone let me know what is cr? in other words, what is the
> default?
> > > > >
> > > > >Also either means whether the addition of both inbound and outbound
> > > > >traffic?
> > > > >
> > > > >How can I verify?
> > > > >
> > > > >
> > > > >Regards,
> > > > >Ravi
This archive was generated by hypermail 2.1.4 : Thu Jun 20 2002 - 22:33:23 GMT-3