From: Andrew Maskell (amaskell@xxxxxxxxx)
Date: Fri Oct 12 2001 - 17:05:13 GMT-3
I have found two possible solutions but have not tested in the lab try:
int bri0
no peer neighbor-route
This prevents the /32 route from being placed into the routing table.
http://www.cisco.com/univercd/cc/td/doc/product/software/ios120/12cgcr/dial_
r/drprt2/drppp.htm#4922
Also a colleague suggested:
> Two available commands should be used as follows:
> Interface xx
> ospf database-filter all out
> router ospf xx
> neighbor xx.xx.xx.xx database-filter out
Have fun!
-Andrew
> -----Original Message-----
> From: nobody@groupstudy.com [mailto:nobody@groupstudy.com]On Behalf Of
> Morse, Doug W (Doug)
> Sent: Thursday, October 11, 2001 7:10 PM
> To: routerjocky; ccielab@groupstudy.com
> Subject: RE: ospf demand circuit (was Re: weird things in IOS ?)
>
>
> I have the same problem in my lab. The last lab I had setup it worked
> but not in this one. Under sh ip ospf int the bri0/0 says that hellos
> are suppressed, Expires the dead timer
> 136.36.21.1 1 FULL/ - - 136.36.5.78 BRI0/0
> follows the dialer idle timeout, disconnects briefly , then dials right
> back and starts the process
> over again. Hellos are not keeping the link up but are bringing it up
> when my understanding of the ospf demand circuit behavior is that they
> should'nt. No changes in the link state database either.
> Time until disconnect 2 secs
> Connected to 72430 (Router4)
> Dial reason: ip (s=136.36.5.77, d=224.0.0.5)
>
> Thanks,
>
> Douglas Morse
>
>
> -----Original Message-----
> From: routerjocky [mailto:elouie@yahoo.com]
> Sent: Thursday, October 11, 2001 1:41 PM
> To: ccielab@groupstudy.com
> Subject: ospf demand circuit (was Re: weird things in IOS ?)
>
>
> is anyone having problems with demand circuit not suppressing hello's?
>
> I can't keep my bri down even though sh ip ospf int shows that hellos
> are
> suppressed. However, the dialer cause is a packet from the bri IP to
> 224.0.0.5
>
> -e-
>
> ----- Original Message -----
> From: "Joseph Ezerski" <jezerski@broadcom.com>
> To: "'Michael Le'" <michael.le@lendlease.com.au>;
> <ccielab@groupstudy.com>
> Sent: Thursday, October 11, 2001 10:01 AM
> Subject: RE: weird things in IOS ?
>
>
> > I too have noticed wierd things in 12.0.7T. In my case, it was an
> OSPF
> > neighbor relationship with an ASBR. The way I do my OSPF commands is
> like
> > this:
> >
> > router ospf 1
> > network 10.1.1.1 0.0.0.0 area 0
> >
> > This lets me tightly control which interfaces participate in OSPF. I
> spent
> > the better part of 2 hours checking and double checking everything
> under
> the
> > sun, including reboots, process kills, even wiping that router....only
> to
> > find that if I put the following, it worked:
> >
> > router ospf 1
> > network 10.1.1.0 0.0.0.255 (or other inverse variations)
> >
> > It seems that 12.07T doesn't like the "all zeroes" inverse mask in
> certain
> > OSPF scenarios.
> >
> > -Joe
> >
> > -----Original Message-----
> > From: nobody@groupstudy.com [mailto:nobody@groupstudy.com]On Behalf Of
> > Michael Le
> > Sent: Thursday, October 11, 2001 3:29 AM
> > To: ccielab@groupstudy.com
> > Subject: weird things in IOS ?
> >
> >
> > Hi Group.
> > IOS doesn't seem to like me lately (12.07T)
> >
> > a virtual link statement is only partially working
> >
> > show ip ospf vir(shows its up and happening) - so i tried
> > Rebooting all the routers, clearing ospf processes etc ...
> > Nothing worked, just had to remove the command and put it in again,
> works
> > straight away ?
> >
> > I've experienced similliar things in isdn confguration also.
> >
> > Any comments would be appreciated.
> >
> > Thanks.
> >
> >
> >
> > Notice: This email is confidential and may contain copyright material
> of
> > Lend Lease. If you are not the intended recipient, please notify us
> > immediately and delete all copies of this message. It is the
> > responsibility of the recipient to virus scan this email.
This archive was generated by hypermail 2.1.4 : Thu Jun 20 2002 - 22:33:18 GMT-3