RE: ISIS over Frame Relay -

From: Armon Richardson (ar28@xxxxxxxxxx)
Date: Thu Sep 13 2001 - 13:19:30 GMT-3

Next message: Tony Olzak: "RE: HSRP load sharing with redundant circuits"
Previous message: Darren Ward: "Re: RTP Lab - next week"
Maybe in reply to: Piperw222@xxxxxxx: "ISIS over Frame Relay -"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ] [ attachment ]

Use the frame-relay map clns (dlci) if using a physical interface.
Verify that you don't have a hello mismatch (ex. physical at the Hub and
subs
at the spoke). I have seen this error message CLNS: System ID
(0000.E01E.3E8C.00)
must not change when defining additional area addresses; and it stems from
adding
a net incorrectly and then trying to readd it. The solution is to just
remove the
ISIS routing process and then readd the net correctly. (also check your
address
you should follow the Gosip Nsap format or the OSI address format)

Gosip Nsap address
                Domain |
        47.0005.80.ffff00.0000.ffff.0004.0000.0c00.62e6.00
         | | | | | | | | |
         | | | | | | | | |
        AFI IDI DFI AAI Resv RD Area System ID N-selector

thanks,

" Where the willingness is great, the difficulties cannot be great "

Armon Richardson
CNE, MCSE, CCNP, CCDP
Network Systems Engineer
Lucent Worldwide Services
pager 1-800-467-1467

-----Original Message-----
From: nobody@groupstudy.com [mailto:nobody@groupstudy.com]On Behalf Of
Raji Mohan
Sent: Thursday, September 13, 2001 11:33 AM
To: jonatale@earthlink.net
Cc: Piperw222@aol.com; ccielab@groupstudy.com
Subject: Re: ISIS over Frame Relay -

Hi,

Please post your configs. Additionally you might want to check and ensure
that the kind of intf match on both ends bcos ISIS does not have any kind
of cmd similar to 'ip ospf network <type> ' to match hellos. So if you
have point-to-pt intf on one end , the other end also has to be the same.

Check and email ur config.
/raji

On Thu, 13 Sep 2001 jonatale@earthlink.net wrote:

> There was a big discussion on this mailing list about 3 weeks ago -- I
think
> basically ISIS can only work over p2p and bcast/full-mesh, not over
> NBMA/partial-mesh/hub-spoke.
> ccielab@groupstudy.com
>
>
>
> Piperw222@aol.com wrote:
>
> > Can anyone please post working configs for ISIS over Frame relay...
Please
> > let me know the configs for sub interface on the hub as well as without.
I am
> > having problems forming an adjacency over the Frame relay cloud. I need
a
> > very simple config for hub and spoke...
> >
> > I am also getting problems when configuring the area address and system
id -
> > I wanted to use the address of the Ethernet put when posted it into the
> > router I got the following error message.
> >
> > %CLNS: System ID (0000.E01E.3E8C.00) must not change when defining
additional
> > area addresses
> >
> > Thanks,
> >
> > Lou
> > **Please read:http://www.groupstudy.com/list/posting.html
> **Please read:http://www.groupstudy.com/list/posting.html
**Please read:http://www.groupstudy.com/list/posting.html
**Please read:http://www.groupstudy.com/list/posting.html

Next message: Tony Olzak: "RE: HSRP load sharing with redundant circuits"
Previous message: Darren Ward: "Re: RTP Lab - next week"
Maybe in reply to: Piperw222@xxxxxxx: "ISIS over Frame Relay -"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ] [ attachment ]

This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 10:32:16 GMT-3